GMH6185XVQ3 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Denver, CO
- Parts Used:
- W10208631A, 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Filter dirty
I unscrewed the filter cover, replaced the charcoal filter and replace the cover. The other wire mesh filter slides right into place. You sent me the right parts for my filter replacement on my microwave. Easy install. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethel from New Berlin, WI
- Parts Used:
- 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed a clean filter
Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Oakland, NJ
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
changed filters
Replaced filter which came inrecord time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Londonderry, NH
- Parts Used:
- 8206232A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out light bulb
The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ferol from San Antonio, TX
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 burned out bulbs under the microwave/important light source for kitchen stove.
I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.
Was this instruction helpful to you?
Thank you for voting!
replacing filter
To replace charcoal filter in microwave, had to take grill off. Tabs on 2 of the 3 screws were fractured and then glued. This happened at the factory. Found Parts Select on the internet who had the grill and filter. Received parts in less than 5 days. Grill was easy to install as the 3rd tab had been eliminated on the replacement part. THANKS PARTS SELECT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Southfield, MI
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace filter
Time to replace the charcoal filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Rock Island, IL
- Parts Used:
- W11661547
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy turntable motor
Unplug microwave. Remove turntable and support from inside. Remove outside bottom cover (10 screws). Remove 2 torx screws holding motor in place. Remove 2 wires from motor, noting colors. Wires are held with spade connectors that has a small tab that needs to be depressed. Remove washer from motor and place on new motor. Entire procedure very easy.
Was this instruction helpful to you?
Thank you for voting!