WMH2175XVQ3 Whirlpool Microwave - Instructions

No repair- just replaced glass turntable.
Right part I needed with first try

The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the light bulb so that we do not need a screwdriver to remove the door to get to the light bulb

I first went back Lowe's where I purchased my microwave in the hopes they would help in the ordering of the grill vent for my mircrowave. They advised me that they do not order parts and gave me a card of a company to call to order the part. I called the number on the card and was left on hold for 20 minutes then instead of helping me with the part I needed they proceeded to set up an appointment for someone in my local area to come to my home, order the part the later install. I knew that it was just 2 screws and bottom snaps to install and I didn't want to wait a week for someone to come to my home. I then went direct to the Whirlpool web-site and found "Partselect.com". I was unable to match my model# even though my microwave was only 13 months old but knew it was probably interchangeable with another so I then called "Partselect.com" and was just amazed at how helpful and knowledgeable the gentleman on the other end was. He found my part and was very patient in describing it to me to assure that it was the correct one. I was on the phone less than 10 minutes with him. The part came in 3 days and was the correct part:) It took me less than 5 minutes to gently snap the 2 bottom tabs in and screw in the left and right tabs on top. Thank you so much "Partselect.com" for making what could have been a timely and expensive part replacement be so very simply and inexpensive.

Removed 1 screw, removed "burnt out" bulb and replaced it with new bulb.

PartSelect had the turntable I needed at the best price. Ordering was easy, but best of all, the part was delivered next day. I was able to insert the new turntable plate into the microwave and it was good as new.

Opened the box and popped it in. No problem with that.

This was an over-the-range microwave/hood, so the replacement parts were significantly cheaper than buying a new unit.

Take microwave down (really a two-person job). Remove microwave cover (about 20 philips screws), discharge HV capacitor by shorting terminals to microwave case. Take photos before pulling anything apart. Remove plastic ducting covering part of the magnetron (3 philips screws). Remove old magnetron (4 Torx screws), need to disconnect small thermostat on side (2 philips screws) and replace with new magnetron. Replace HV diode (screw on one end, other end simply plugged into capacitor terminal). Put everything back together and it works fine.

The part was sent to me the next day! And it was the right part. Awesome!

set the table on the support ring

This is the second replacement tray we have in installed. The first one ( Not From Here ) we had for less than 5 months, we made a bag of popcorn, and about 5 minutes later we heard a crash, not knowing where the noise came from we dismissed it. The next day we opened the microwave a saw the plate had shattered. So we hope that this will not do the same thing.

Unless you have a very comfortable background with electronics and electricity, I don't necessarily recommend taking apart a microwave. If you are very handy and are going to be VERY cautious to follow the rules of discharging caps and testing voltages before moving forward, then go for it. That said, I took the microwave off and apart. Not knowing where to find the parts, I was fortunate that the installer put the instruction book for the microwave inside the front vent slot above the touchpad for reference. it details the location of every part and it tells you very clearly what each part you test should show specific to this microwave on your multimeter. Find this guide online if you don't have it. Turn on the microwave for 20 seconds with a glass of water to make sure it's not heating - that with the noise means it's eeither the magnetron, cap, or diode. Read the notes on this site for all of the basic things to look for with the magnetron, diode, and capacitor. Once comfortable with the guide, locations of those devices, and how to test, then take it down and apart. Unfortunately, I didn't do all those things in that order, and it only wasted a lot of time trying to find the parts. Once I found the parts and put all the screws and covers back for all the areas that didn't need to be accessed for the repair, testing went quickly. The diode was bad. Ordered a new one and had it in 3 days or so. That means your microwave will be apart and sitting somewhere for a little while until you get the part and have time to repair it. Putting the diode back isn't too bad. Reassemble the microwave and put it back up again. If i had to do it again, it would take me 20 to 30 minutes once the microwave was down and on a table. Also, I used some bricks with towels over them or you could use some sawhorses to keep the microwave elevated so you can plug it in and run it after installing the new component. Again, make sure you discharge the cap before touching anything again even if you didn't run it, but just plugged it in.

I turn off the income electricity by shutting down the corresponding circuit breaker. Then, I removed the control panel from the microwave which gave me access to the capacitor and adjacent diode. After that i unscrewed the defective diode and replaced it with the new one and BINGO!

removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

Unplugged the microwave to de-energize the unit. Removed 1 screw and the shroud on the range hood light; removed the light bulb. Removed 4 screws from each side and the front of the metal plate on the underside of the unit. Carefully lowered the plate to expose the light socket. Noted which wire was connected to each terminal (they are color-coded), then released the spring clip connectors from the terminals. Removed the 1 screw holding the socket in place then reversed the procedure to install the replacement parts.

I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to catch enough to hold the glass plate in position and left it at that.