YMH2175XSS3 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOHN from Marana, AZ
- Parts Used:
- 8206394
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
The star broke when trying to loosen the bolt at the top
I had to hammer out the broken star wrench tip then progressively drill the head off of the bolt. Once accomplished I could remove the door. I used a standard replacement screw I case I ever have to replace the door again. The manufacturer should use a fastener other than a star head bolt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roger from palm coast, FL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace light blub
removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Kannapolis, NC
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass cooking tray for microwave cracked.
All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amber from Loretto, PA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass tray in the microwave got chipped while i was washing it and started to crack.
I just opened the box and set it in. Took all of two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vanessa from Atlanta, GA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass cooking tray for microwave
Twas really easy considering that all I had to do was place the plate back in the microwave. Easy Peasey
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Rhinelander, WI
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass microwave tray
Tray arrived in a short period of time and was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from Leesburg, FL
- Parts Used:
- W10269471
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
vENT gRILLE SHATTERED
FOLLOWED EASY INSTRUCTIONS VIA THE WEB.Note: I am a widow...83 yrs of age. Thanks for making it easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethel from New Berlin, WI
- Parts Used:
- 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed a clean filter
Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Winter Park, FL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken cooking tray. Food not heating evenly.
Simply placed new dish on the rotating hub.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Harbor Beach, MI
- Parts Used:
- W10269471
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
It was cracked by the screws.
I took the old one off and put the new one up opened the door to do it and used a magnetic phillips screwdriver.I did not need help from the husband .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Saundra from Live oak, TX
- Parts Used:
- 8206393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Exhaust vent broke off
Uncrewed existing screws. Slipped on new vent tighten screws finished
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from BULLARD, TX
- Parts Used:
- 8206393
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer Stopped Drying Completely, Timer Didn't Shut It Off.
1. Safely unplug the dryer. 2. Unconnect the vent hose. 3. Pull it out so you can have room to move around to work on it. I actually in a power chair so I put an old blanket on the floor and laid it face down to work on it. It was extremely dirty so I used a shop vac to clean off the back panel before starting. 4. I took off all the screws and cord cover with a nut driver, used the shop vac again to clean the entire inside. Properly a 1/2 to 1 inch of dust and lint was built up causing a dangerous fire situation for sure. Once clean, take a photos especially of where the electrical connection are. 5 Located and removed the two screws holding the element on, used a nut driver and long nose pliers to remove the heat sensor & electrical connections. 6. Dry fit the element before tightening screws to make sure placement is correct then match the holes replace the screws. 7. Using the photos put the heat sensor & electrial wires back on, you may need to use the pliers to push it on tight. Double check everything, clean back panel inside and out, match up holes replace screws, I actually checked my power cords screws for tightness then replaced cord cover. 8. Replace vent hose if needed or then reattach it and plug it up. You may need to check the dryer barrel by turning the drum around a few times. Should work perfect, you will smell the element a little but it should be ok. Remember clean your dryer inside and out every six months or so to prevent dryer fires.
Was this instruction helpful to you?
Thank you for voting!
Bulb Burnt Out Stuck In The Socket On Microwave
I ordered bulb, which was stuck in socket. Order a new bulb amd socket, now is working fine thank you for your help and having the part we needed, it was delivered in a couple of day and now is working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Anniston, AL
- Parts Used:
- W10269471
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The vent grille mounting brackets broke
The old grille would not stay in place since the mounting brackets disintegrated. I wired the old grille in place for aesthetics and ordered a new one. When the new grille arrived (very promptly I might add)I removed the old grille and mounted the new one with the old screws. It would have been nice if the new part had included new screws because I lost one of the old ones. But I have a cache of old screws so I found a replacement that worked. I was very pleased to find the new part so easily!
Was this instruction helpful to you?
Thank you for voting!