MH1170XSQ3 Whirlpool Microwave - Instructions

I had to hammer out the broken star wrench tip then progressively drill the head off of the bolt. Once accomplished I could remove the door. I used a standard replacement screw I case I ever have to replace the door again. The manufacturer should use a fastener other than a star head bolt.

I ordered bulb, which was stuck in socket. Order a new bulb amd socket, now is working fine thank you for your help and having the part we needed, it was delivered in a couple of day and now is working

Removed all the screws from the underside panel - approximately 9 or 10 of them. The panel easily dropped down to allow easy access to the light bulb socket assembly. The wires to the socket easily unplugged and old socket easily removed. New socket slipped right in and wires easily plugged in. Actually took longer to put the screws back in than anything else. I am thrilled with this repair. Note: so easy even a 61 year old single woman in her PJ's can do it.

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

Had to take all the screws out of the bottom of the microwave to get to the socket. Once that was done, it was a simple fix of taking out 2 screws that hold the socket in, and then unplugging it. Replug and put all screws back. It was a fairly simple fix for the diy homeowner.

1. Safely unplug the dryer. 2. Unconnect the vent hose. 3. Pull it out so you can have room to move around to work on it. I actually in a power chair so I put an old blanket on the floor and laid it face down to work on it. It was extremely dirty so I used a shop vac to clean off the back panel before starting. 4. I took off all the screws and cord cover with a nut driver, used the shop vac again to clean the entire inside. Properly a 1/2 to 1 inch of dust and lint was built up causing a dangerous fire situation for sure. Once clean, take a photos especially of where the electrical connection are. 5 Located and removed the two screws holding the element on, used a nut driver and long nose pliers to remove the heat sensor & electrical connections. 6. Dry fit the element before tightening screws to make sure placement is correct then match the holes replace the screws. 7. Using the photos put the heat sensor & electrial wires back on, you may need to use the pliers to push it on tight. Double check everything, clean back panel inside and out, match up holes replace screws, I actually checked my power cords screws for tightness then replaced cord cover. 8. Replace vent hose if needed or then reattach it and plug it up. You may need to check the dryer barrel by turning the drum around a few times. Should work perfect, you will smell the element a little but it should be ok. Remember clean your dryer inside and out every six months or so to prevent dryer fires.

The repair was very simple. only had to remove two screws and replaced the broken grill.

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

Watched video which reminded me to order support for the turntable support ring and did exactly what the person in the video did. Excellent and prompt service and all parts fit.

After researching online, I found that I needed the turntable drive coupling, part#PS993087. when I went to your site it showed the same part but the part number had changed but said it would fit my microwave. Well, I was really surprised and happy when the part I received 3 days after I placed the order, with normal shipping,fit perfectly and now my turn table in my microwave works. I have marked this site a a favorite and will use it I'm sure soon. Being a single women and having to figure out how to fix the things on a small buget, I'm learning a lot and have a lot of respect for men that know how to do all the repair stuff. Thanks so much, I have been able to mark this off my list of things to fix. Have a nice day. Cj- age, 58

Simply placed new dish on the rotating hub.

I took the old one off and put the new one up opened the door to do it and used a magnetic phillips screwdriver.I did not need help from the husband .

replaced burnt parts

First let me say that I tried several places to get what I thought was a simple light bulb. This included several national hardware stores as well as a national electrical supply company. No luck. Went to the manual and PartSelect. Not only did you have it in stock, ship right away,at a reasonable price it arrived in a matter of days. One would not normally think of receiving a "how to" video to change a light bulb but you did. That impressed me. Suffice to say the replacement went well and you can be certain the next time I need a part I will go to you first. I am also impressed with the organizations with which you are affiliated with. BBB, Norton, PayPal, money back guarantee etc. Thank You The entire process was made pleasant with your support.

A plastic tab, 1 of 3, on the plastic replacement vent grill had to be hand filed to make it fit in the slot on the microwave. The other 2 were fine. It is an obvious quality control issue from the manufacturer's injection mold or inspection process that allowed the extra plastic to remain on the tab.