MH1160XSD3 Whirlpool Microwave - Instructions

just replace need cooking tray

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

1. Safely unplug the dryer. 2. Unconnect the vent hose. 3. Pull it out so you can have room to move around to work on it. I actually in a power chair so I put an old blanket on the floor and laid it face down to work on it. It was extremely dirty so I used a shop vac to clean off the back panel before starting. 4. I took off all the screws and cord cover with a nut driver, used the shop vac again to clean the entire inside. Properly a 1/2 to 1 inch of dust and lint was built up causing a dangerous fire situation for sure. Once clean, take a photos especially of where the electrical connection are. 5 Located and removed the two screws holding the element on, used a nut driver and long nose pliers to remove the heat sensor & electrical connections. 6. Dry fit the element before tightening screws to make sure placement is correct then match the holes replace the screws. 7. Using the photos put the heat sensor & electrial wires back on, you may need to use the pliers to push it on tight. Double check everything, clean back panel inside and out, match up holes replace screws, I actually checked my power cords screws for tightness then replaced cord cover. 8. Replace vent hose if needed or then reattach it and plug it up. You may need to check the dryer barrel by turning the drum around a few times. Should work perfect, you will smell the element a little but it should be ok. Remember clean your dryer inside and out every six months or so to prevent dryer fires.

I ordered bulb, which was stuck in socket. Order a new bulb amd socket, now is working fine thank you for your help and having the part we needed, it was delivered in a couple of day and now is working

replaced burnt parts

Removed 2 screws on the top of the microwave and removed top/front piece of microwave. Slid out old filter (which didn't look dirty at all) and replaced it with the new one. Replaced top/front piece and 2 screws. It took less than 5 minutes.

I had no problem installing the new filter. Just used a phillips screw driver to remove the two screws holding the vent cover in place. Cleaned the dust out of the ducts and reinstalled the new filter. The screws must be held to the screw driver with your finger tips so you don't drop them in the vent cover. The most difficulty I had was in clearing the clean code from the screen. There are no instructions in the owners manual for doing this. But after several tries I got it.

Replaced light bulb.

Attached bracket to wall with screws and hung microwave oven. Very easy project.

Removed the glass cover and replaced the bulb. Very simple.

The lady in the Nova Scotia call center should get all the credit for being able to identify the part I needed from only the very limited information I was able to give her. Employee of the month for her. She also had such a great can do attitude. Lawence Baier

My husband open the microwave and see the capacitor melted. He try to find the piece in store,but unfortunatly he didn't find any. I found the piece on the web and ordered it. My husband replaced the part easily. The microwave work very well.The microwave was to our friend. He did replace it by a new one. Now we have a new microwave with a fan.

--simpley removed 2 screws, removed old filter--but had PLENTY of cleaning to do before putting in the new filter !My husband LOVES to cook and pan fry foods--it won't go that long before being replaced in the future!

Easy, perfect