IMH16XVS1 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gail from Cincinnati, OH
- Parts Used:
- W11252182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turntable broke in half, ring turn needed replaced
I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next
Service was fantastic, parts were ordered one day and received the next
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from CARPENTERSVLE, IL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
light bulb burnt out .
Turn off power supply at breaker . Replace old bulb with new bulb .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANNY from SAINT JOHNS, FL
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light in microwave
Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Port St Lucie, FL
- Parts Used:
- W10435116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable coupling
Rep knew exactly what I needed when I described where the part should go on my microwave - price great - shipping great - installed in seconds. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from ARVADA, CO
- Parts Used:
- 4393799
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I had broken the glass turn table.
I ordered another one and placed it inside the microwave. It works and fits perfectly. I received the order exactly as scheduled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Pine, CO
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replacement of hood light bulbs
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon C from MEDFORD, OR
- Parts Used:
- W11252182
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Microwave didn't have support ring when house was purchased.
Removed turntable
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from OVERLAND PARK, KS
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out bulb
Husband replaced the bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily C from Brandon, MS
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped the glass cooking tray and it broke in half
Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!
E. Robinson
E. Robinson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from CENTENNIAL, CO
- Parts Used:
- W10435116
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drive coupling cracked would no longer rotate turntable plate
used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts
Very Pleased with Parts Select replacement parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from LIVERMORE, CA
- Parts Used:
- W10269232
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Terminal leads were too wide on the thermostat.
I had to cut the leads on the thermostat to enable the wire terminal clips to fit on the leads. Not hard at all when the right tools are available. Care must be used because the leads are subject to being damaged. “ Hold leads with narrow needle nose pliers while cutting!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRIS A from NEOSHO, MO
- Parts Used:
- W10754299
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave not heating very well
Took microwave off the mount, removed all the outer covers except the face, used metal screwdriver to short the big capacitor to keep from being shocked, removed magnetron and replaced with new part. Put back together, hung on wall, and finished. I used a youtube video and it turned into a very simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monty from Mansfield, TX
- Parts Used:
- W10642989
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace turntable motor
removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.
Was this instruction helpful to you?
Thank you for voting!
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myra from WATERFORD, ME
- Parts Used:
- 8206229A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
when putting my grease filter back in place it dropped behind my stove.
I placed a thick towel by the opening at the top of my stove and was able to fit the new grease filter in with no problem
Was this instruction helpful to you?
Thank you for voting!