GH6177XPB4 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jorge from Bay Point, CA
- Parts Used:
- 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulbs nedd to repace it.
Took the the want burned out , and put the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patti from Coarsegold, CA
- Parts Used:
- 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Burned Out
Followed the instruction booklet that came with the microwave. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kymberly from Beaumont, CA
- Parts Used:
- W10113040A, W10112514A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Grease & Fiter vents
I want to thank PartSelect for thier assistance with my grease and filters that were needed for our microwave. We just bought a home and although the appiances are still in good working condition and only 6 years old they have not been maintaned well at all. The filers needed replacing and our local chain of hardware stores do not carry any of the sizes we needed. I went on line and found PartSelect.com and reviewed what they offered. I really could not find what I needed so I called customer service and the women on the other end of the phone went through in great detail as to the sizes and quantities I would need. I have since then received the filters and they were extremely easy to install and fit perfectly. Very helpful site. KDS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Tampa, FL
- Parts Used:
- W10450189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The microwave grille vent was cracked and the clip was broken.
The replacement grille fit to factory specs, requiring a simple snap in place installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JASON from ABSECON, NJ
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plate
Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Huntington Beach, CA
- Parts Used:
- 8184581
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Microwave was making a grinding sound
Problem was easily diagnosed using the internet as a resource, problem was a bad stirrer motor. Hardest part of the repair was the removal of the microwave. Once off the wall, you remove the outer cover and a molded plastic casing directly underneath the outer cover at the top of hte microwave to expose the stirrer motor. Removed two screws and two wires and the old motor is out. Did exactly the opposite to install the new motor. The kit I recvd included among other things the motor, a new inside cover, plastic rivets and even silicone to seal the inside cover. I am sure I saved a couple hundred dollars by doing myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larrt from Minooka, IL
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dotty from Hillsboro, WI
- Parts Used:
- 8204670
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
surface light on microwave wasnt' working
took the light assembly off and replaced the bulb and put the assembly together and fitted back in the space and finished the assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from Bartlett, IL
- Parts Used:
- W10450187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
soap and rinse aid were not dispensing
I removed the front cover, which allowed access to the soap dispenser. You need a 1/4" driver set to unscrew the dispenser. I installed the new dispenser, and the dishwasher worked great. The inital problem of the soap door not opening, and the rinse aid not dispensing, was solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Salem, CT
- Parts Used:
- W10450189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems
Easy install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amber from Loretto, PA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass tray in the microwave got chipped while i was washing it and started to crack.
I just opened the box and set it in. Took all of two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Statham, GA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement
Easy, perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugenio from San Jose, CA
- Parts Used:
- W10450172
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken clips and plastic pieces holding tabs
The only to repair the vent grill was to purchase a new one. I went ahead and found a the replacement part and waited 5 days when it arrived. Very easy installation. Ijust lined it uap amd popped it in place. With a screwdriver I made sure to extend the clips slightly to ensure they fit snuggly to ensure they held the vent tightly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from White House, TN
- Parts Used:
- W10450187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Vent/Grill cover
Received new cover the next day. Snapped new cover in place with no problems.
Was this instruction helpful to you?
Thank you for voting!