MH3184XPQ1 Whirlpool Microwave - Instructions

Open compartment, installed bulb, closed compartment

Part was easy to order on a secure site. The filter will make a difference as our appliance is not externally vented.
Good people to deal with.

Snapped it back on. However, I made a mistake and ordered the wrong color. You wree great, shipped the right one the same day, and took the other one back.Thank you.

The two repair items were exactly right and just snapped into place.

took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse

The repair was easy, I just took off a few screws and found the broken latch spring. The real story is how easy it was to find the replacement spring from Partselect! I couldn't believe they had it, and even better yet, I ordered it one afternoon, and it came the next day with normal shipping! Unbelievable! Then I just popped it in and replaced the covers I had removed and it was working again!

Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!

This is an over stove top mounted oven. Remove oven from mount and place on a work surface with padding to support the lamps and vent holes. Strip the case off and locate the noted other "most likely" parts. Watch out for the Capasitor. Read the test note available for each part; Diode, Thermister Fix, Capasitor and Magnitron. Do the test checks. My issue wasn't obvious because I think the Capasitor was discharged and needed to be hot to check the Magnitron. (I'm not an electrical engineer so...) At this point I did the foolish thing...I plugged the unit in and ran it. Watching from a distance I saw sparks fly from the top side of the Magnitron with the same result from my cup of water (cold-no sprks here.) I replaced the diode and tried again, same result. I ordered the Mag and the Thrmst-Fix. Thrmst-Fix was on BO when the Mag got here so I installed the part. Had to remove several pieces to afford room to work and still had to stretch and pry to get the old out and new in. Mag is held in place with Torx screws so check that before you start. No other tool works. Mag was the problem for this unit. Some problems encountered: Parts and pieces were quick in arriving as long as they were not Back Ordered. Be careful to follow a thread for your product to order parts. These review/instructions are mixed for simular appliances and sometimes lead off to other part lists and numbers. Prices differ from model to model, list to list and the part numbers change. Go back to your product and then trace for the correct parts. I noted a $40 price dif.between Magnitrons from simular part lists. When you receive the part check to match the part numbers, Manuf. no. are different from the Part Select No. but can be crossed. Otherwise using this site's instructions, checks, insulated tools, big rubber gloves and a face shield I managed to save a $600 machine from the junk pile. Parts as ordered were recieved and return of un-touched parts were accepted by Parts Select without unexpected hassle. Thanks for a positive experience.

Problem was easily diagnosed using the internet as a resource, problem was a bad stirrer motor. Hardest part of the repair was the removal of the microwave. Once off the wall, you remove the outer cover and a molded plastic casing directly underneath the outer cover at the top of hte microwave to expose the stirrer motor. Removed two screws and two wires and the old motor is out. Did exactly the opposite to install the new motor. The kit I recvd included among other things the motor, a new inside cover, plastic rivets and even silicone to seal the inside cover. I am sure I saved a couple hundred dollars by doing myself.

I removed the front cover, which allowed access to the soap dispenser. You need a 1/4" driver set to unscrew the dispenser. I installed the new dispenser, and the dishwasher worked great. The inital problem of the soap door not opening, and the rinse aid not dispensing, was solved.

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

Removed all the screws from the underside panel - approximately 9 or 10 of them. The panel easily dropped down to allow easy access to the light bulb socket assembly. The wires to the socket easily unplugged and old socket easily removed. New socket slipped right in and wires easily plugged in. Actually took longer to put the screws back in than anything else. I am thrilled with this repair. Note: so easy even a 61 year old single woman in her PJ's can do it.

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.

Arrived in 24hours!!! Great.