MH2155XPS2 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerry from Pine, CO
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replacement of hood light bulbs
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lea from FRANKLIN, TN
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken tabs
We took a chance on the less expensive black Whirlpool vent grille as I found online that it would fit our stainless steel Kitchenaid microwave. My husband was able to pry the stainless cover off the broken grille and snap it onto the new black one. Then just screw in the top screws to secure. We are very happy with the stainless/black of the new setup. It goes very well with the stainless/black of the cooktop and oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from W. Dover, VT
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Grill
Snapped and screwed new part in minutes
Was this instruction helpful to you?
Thank you for voting!
light that illuminates the range would not work.
replaced the socket per recommendations on this web site. this did not correct the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from DALLAS, TX
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic on original grill clips broke.
Took out 2 phillips screws on top, pulled the old grill out, hooked the tabs on the bottom of the replacement into place, positioned the top of the replacement, and replaced the 2 screws. 5 minutes. NOTE: Save the screws, new ones don't come with the replacement grill.
Was this instruction helpful to you?
Thank you for voting!
The old coupling melted and the tray cracked in half.
It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!
Was this instruction helpful to you?
Thank you for voting!
smoke alarm went off while frying
both of the pieces have a tab that help remove the pieces. They slip right out and new ones are putin place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois P from Morris, IL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke rotating plate, it fell off counter after being washed
Opened door and put new plate in.
Placed order on Thursday evening and received Sat Am
Placed order on Thursday evening and received Sat Am
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from ORANGE, CA
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from CENTENNIAL, CO
- Parts Used:
- W10435116
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drive coupling cracked would no longer rotate turntable plate
used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts
Very Pleased with Parts Select replacement parts
Was this instruction helpful to you?
Thank you for voting!
Microwave worked perfectly but would no longer heat.
Looked up symptoms on parts select website. Ordered mag and diode. Very easy to take micro off the wall. Easily removed screws holding the skin on. Found diode. Really didn't need to replace it but since I had a new one (fairly cheap), just did so. Diode only installs one way. Can't botch it HOWEVER, MAKE SURE THE ONLY PART OF THE DIODE TO TOUCH THE GROUNDING POLE IS THE SCREW DOWN LEAD. IF THE OPPOSITE END LEAD, THAT WHICH IS THE PUSH ON TERMINAL, TOUCHES THE GROUNDING POLE, YOU'LL GET ARCHY SPARKY. The magnetron goes in very easy. Simply pay attention to how you removed it and reverse that process installing the new one. There are easy to use YouTube videos that show magnetron replacement. You can do this easily and save your microwave and $$ while doing so.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HARKER HTS, TX
- Parts Used:
- W11707984
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Microwave had no electrical
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Upland, CA
- Parts Used:
- 8184608
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grille broke off the microwave-fell off
Placed to new grille on the microwave and attached
with the screws.
with the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colan from Fargo, ND
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Vent Grill Fell Off
My vent grill fer me microwave done and fell off.
Was this instruction helpful to you?
Thank you for voting!