YMH7155XMS0 Whirlpool Microwave - Instructions

took door panel off and than took handle off door pannel. took glass out of old door panel washed it and slid it in the door panel very gently until it snapped into place. then I lined up the door on the left side and snapped it in gently into place and put the 3 screws in and complete. about 15 minutes. I read that it was very difficult but that is not so.

Removed the old grill. Then loosened the screws on the top of the microwave. Popped the grill in place and tightened the screws. it looks great, works perfectly, and we don't have to replace the unit that we were afraid might be the case.

thanks so much for providing these parts that saved us from buying a new microwave oven.

removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to catch enough to hold the glass plate in position and left it at that.

Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.

I made a video. There were specific instructions to note which needed to be explained. Interested?

The hard part was trying to find the light bulb locally. The locally sold light bulbs were either too long, not dual element or not powerful enough. So I ordered the light bulb straight from PartSelect. When it came time to install the new light bulb I carefully removed the screw holding the plate in position so as not to loose it in my gas stove. I needed the mirror to line up the light bulb and screw it in. Once it was in I verified operation and closed up the plate being careful not to drop the screw into my gas stove. Problem solved.

I found the part number for the mount on the appliances company website. Once I had that I visited a few sites looking for part. This site was easy to use and priced right, so I ordered. A few days later the product arrived as promised and worked perfectly for the install.

KitchenAid Microwave [Model: KHMS 145 JBS-0]Door Handle Repair
Tools and Parts
• Door Handle [Part # PS390101]
• Putty Knife
• Phillips Screwdriver
• Tray (cup) for parts during disassembly/reassembly (3 screws on door; 2 screws on handle; spacer on top-door edge).
Instructions
• Preparation
o Disassembly can be managed with the door mounted on the unit. The handle is attached by 2-screws that can be accessed only by separating the outer/inner door panels.
o Before starting the project, watch the Youtube.com video for a GE Microwave, which is the most applicable video for removing the collar [i.e., plastic bezel around the viewing window on the inner door) and for separating the outer/inner door panels ].

• Remove the collar
Photo 1: Inner-side clip (bottom of collar) used on
3-sides of the collar (top edge is a spacer) Photo 2: Hinge side clip (right edge)

o As indicated in the video, small clips are on the inner-side of the collar on 3-sides (top, bottom, and open-door edge).
o The clips are on the outside of the collar for the door-hinge side.
o These clips are small and somewhat fragile – once a few are popped, finger pressure will generally pop the remaining clips.


• Separate the outer/inner door panels

Photo shows the inner/outer doors separated, and the 3-screws removed.
o Remove the 3-screws on the door edge before separating the outer door panel.
o There is a plastic spacer on the top, outside edge of the door that is not cemented. Remove the spacer after separating the door panels.
o Use a putty knife to pop the clips for the outer-door panel around the top, bottom, and open-door sides.
o The top door corner (the spacer edge) is tight and should be gently pushed back.
o The outer door panel will remain attached on the hinged edge and function like a second door – move gently.
o The viewing glass is clamped in place; but, handle with caution.

• Remove the Door Handle
o With the outer/inner panels separated, remove the two screws holding the handle and remove the handle.
o Retain the screws for later use.

• Install the new Door Handle
o Reuse the original screws (Note, [Part # W10841091 – screw] is a different thread, and is not self-tapping)
o The door-handle screw holes are not tapped; so insert the old screws in the handle to tap before installing the handle, leaving approximately 1/8 - 3/16” exposed.
o Remove the screws and reuse to install the handle.


Comparison of 2-original screws vs. replacement screw (note thread gauge differences).
• Reinstall the Outer Door Panel
o Align the spacer with the inner-panel edge in the upper corner.
o Close the outer panel, gently snapping the clips into place.
o Reinstall the 3-screws on the door edge.

• Reinstall the Collar
o Snap the hinge side in place.
o Gently snap the remaining sides in place

Instead of telling you, i have question do you have any instructions on how to do the repair. It would have helped save time on the repair.

This job took longer then it should have, becasue I did not start right in the begining. I did figure it out quickly after the wrong start.

You were a big help in picking the right part to correct the problem. You should be able to help with the repair. Thank You

I ordered the part according to the Model number, inserted the part very easily, (and I am soooo challenged in that area) and now it turns again. :)

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

This is not easy to do. I done it before to replace a broken window and it was a real bitch. I considered buying a new door rather then do it again.All I wanted to do was tighten two screws that hold the handle.
I used the advice found on your web site from a person who did it using quarters and putty knifes to remove the choke and the door insert. Sounded silly but it works like a charm. I advise anyone who needs to do this repair to use that info on your web site. It will save lots of frustration. Be sure to have plenty of quarters and a few pennies.

I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

the burn thru was probably because stirrer motor was not turning, Unplug the microwave .freed the motor up bu manually turning. temporary fix. The cover is held up with small push pin clips. Just pry the cover off with a screw driver or other flat tool. Scrape offf the old silicone. There are two covers in the Kit. you just need 1. Remove the old clips for the roof of the microwave, put a bead of silicone on the new cover where the old was and secure the new cover with the push pins into the clips .