GH7155XHS1 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- chap from edmond, OK
- Parts Used:
- WP8183507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Approximately 5 seconds into heating something, the microwave went dead
It literally took me longer to unpackage the fuse than to install it. I removed the outer shell by unscrewing the five screws, lifted it off and set it aside. The old fuse was readily visible so I pulled it out and put the new one in its place. I set the shell back on and replaced the screws. I plugged it in and ran it for 30 seconds while still in the shop just to make sure that solved the problem and presto - it worked like a charm. A $20 part saved me from having to purchase a new microwave (sadly, I had to break the news to the wife).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cassandra from Cleveland, OH
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
microwave plate broke
Just took the plate out the packaging & rinsed,dried and put in the oven. I was so happy I found it @partselect online& it came in the next day or two. Will definitely use them again. It was a fraction of the cost from local parts store.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Palmer Lake, CO
- Parts Used:
- 4392027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave worked intermittently
The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from EL Paso, TX
- Parts Used:
- 4359331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
filter was old
simply too the cover off the top vent area and removed the old one and replaced it with the new one
Was this instruction helpful to you?
Thank you for voting!
Replace old parts
remove one screw from light and remove bulbs replace. I found the light plate had a lot of grease on rubber type washer for the glass cover. I cleaned it as best I could. The real trick was putting the screw back in when the Microwave is in with the hood Fan and the screw must go straight up and not miss the hole. I had someone hold the plate up and the screw went in. Your instruction book shows your filters and how to clean them. They are easy to and clean. What I found best is the lights they had been in for 15 years and the new ones are so much brighter. I now have an old set of filters that can be put in the dishwasher and used as a replacement when the new ones need to be cleaned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M. J. from Chester, NH
- Parts Used:
- WP8172138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
I broke the dish in my microwave unit.
I simply went on line to Part Select, placed my order, made payment, and was astonished to see the package with a new dish sitting on my doorstep the next day.Great service.
Was this instruction helpful to you?
Thank you for voting!