GH9185XLT1 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Monty from Mansfield, TX
- Parts Used:
- W10642989
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace turntable motor
removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JASON from ABSECON, NJ
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plate
Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Huntington Beach, CA
- Parts Used:
- 8184581
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Microwave was making a grinding sound
Problem was easily diagnosed using the internet as a resource, problem was a bad stirrer motor. Hardest part of the repair was the removal of the microwave. Once off the wall, you remove the outer cover and a molded plastic casing directly underneath the outer cover at the top of hte microwave to expose the stirrer motor. Removed two screws and two wires and the old motor is out. Did exactly the opposite to install the new motor. The kit I recvd included among other things the motor, a new inside cover, plastic rivets and even silicone to seal the inside cover. I am sure I saved a couple hundred dollars by doing myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Mesquite, TX
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb burned out
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patti from Coarsegold, CA
- Parts Used:
- 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Burned Out
Followed the instruction booklet that came with the microwave. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kymberly from Beaumont, CA
- Parts Used:
- W10113040A, W10112514A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Grease & Fiter vents
I want to thank PartSelect for thier assistance with my grease and filters that were needed for our microwave. We just bought a home and although the appiances are still in good working condition and only 6 years old they have not been maintaned well at all. The filers needed replacing and our local chain of hardware stores do not carry any of the sizes we needed. I went on line and found PartSelect.com and reviewed what they offered. I really could not find what I needed so I called customer service and the women on the other end of the phone went through in great detail as to the sizes and quantities I would need. I have since then received the filters and they were extremely easy to install and fit perfectly. Very helpful site. KDS
Was this instruction helpful to you?
Thank you for voting!