MH3184XPQ4 Whirlpool Microwave - Instructions

Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.

Replaced the supports and rack.

With new replacement grill, a separate clip was supplied in the box that had to be screwed in to the top portion. This clip did not fit since the hole for the screw was on the right side and not the left, so I just snapped the grill in place with the existing clips.
There must be another clip that fits this unit but perhaps the person packing the box grabbed the wrong clip and taped it in with the shipped box.

Rep knew exactly what I needed when I described where the part should go on my microwave - price great - shipping great - installed in seconds. Thank you!

Ordered new part on Thursday night and new part arrived the following Monday. After unpacking I just snapped the new grille in place and the job was done. I was really impressed with the quick service that I received from PartSelect.

Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!

E. Robinson

easy to replace, just the same as cleaning the turntable and placing back in the micorwave;

I called my brother, he is much more proficient with reading instructions and figuring out how they go together,! He had it done in less than 30 mins.! I love my brother!!!

Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together

Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple

Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul