MH1170XST0 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- roger from palm coast, FL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace light blub
removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Kannapolis, NC
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass cooking tray for microwave cracked.
All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Saundra from Live oak, TX
- Parts Used:
- 8206393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Exhaust vent broke off
Uncrewed existing screws. Slipped on new vent tighten screws finished
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Lincoln, NE
- Parts Used:
- W10139642
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
vent grill had manufacturing flaw
A plastic tab, 1 of 3, on the plastic replacement vent grill had to be hand filed to make it fit in the slot on the microwave. The other 2 were fine. It is an obvious quality control issue from the manufacturer's injection mold or inspection process that allowed the extra plastic to remain on the tab.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larrt from Minooka, IL
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from BULLARD, TX
- Parts Used:
- 8206393
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer Stopped Drying Completely, Timer Didn't Shut It Off.
1. Safely unplug the dryer. 2. Unconnect the vent hose. 3. Pull it out so you can have room to move around to work on it. I actually in a power chair so I put an old blanket on the floor and laid it face down to work on it. It was extremely dirty so I used a shop vac to clean off the back panel before starting. 4. I took off all the screws and cord cover with a nut driver, used the shop vac again to clean the entire inside. Properly a 1/2 to 1 inch of dust and lint was built up causing a dangerous fire situation for sure. Once clean, take a photos especially of where the electrical connection are. 5 Located and removed the two screws holding the element on, used a nut driver and long nose pliers to remove the heat sensor & electrical connections. 6. Dry fit the element before tightening screws to make sure placement is correct then match the holes replace the screws. 7. Using the photos put the heat sensor & electrial wires back on, you may need to use the pliers to push it on tight. Double check everything, clean back panel inside and out, match up holes replace screws, I actually checked my power cords screws for tightness then replaced cord cover. 8. Replace vent hose if needed or then reattach it and plug it up. You may need to check the dryer barrel by turning the drum around a few times. Should work perfect, you will smell the element a little but it should be ok. Remember clean your dryer inside and out every six months or so to prevent dryer fires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from Marana, AZ
- Parts Used:
- 8206394
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
The star broke when trying to loosen the bolt at the top
I had to hammer out the broken star wrench tip then progressively drill the head off of the bolt. Once accomplished I could remove the door. I used a standard replacement screw I case I ever have to replace the door again. The manufacturer should use a fastener other than a star head bolt.
Was this instruction helpful to you?
Thank you for voting!
Old light bulb popped and burned out and melded itself to the socket. Light bulb then broke off inside the socket. Socket cracked and broke when trying to dislodge broken light bulb.
Removed all the screws from the underside panel - approximately 9 or 10 of them. The panel easily dropped down to allow easy access to the light bulb socket assembly. The wires to the socket easily unplugged and old socket easily removed. New socket slipped right in and wires easily plugged in. Actually took longer to put the screws back in than anything else. I am thrilled with this repair. Note: so easy even a 61 year old single woman in her PJ's can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ferol from San Antonio, TX
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 burned out bulbs under the microwave/important light source for kitchen stove.
I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JASON from ABSECON, NJ
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plate
Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from La Jolla, CA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke a 15 year old glass cooking tray
Ordered the item on a Monday at 12pm and it arrived the next day. Amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from North Olmsted, OH
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Reminder signal and message to change filter on microwave digital display.
Removed 2 screws on the top of the microwave and removed top/front piece of microwave. Slid out old filter (which didn't look dirty at all) and replaced it with the new one. Replaced top/front piece and 2 screws. It took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Volo, IL
- Parts Used:
- W10269471
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken screw holes
unscrewed the screws and put the new vent in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jocelyne from Fort Pierce, FL
- Parts Used:
- W10850446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The capacitor was melted in the microwave
My husband open the microwave and see the capacitor melted. He try to find the piece in store,but unfortunatly he didn't find any. I found the piece on the web and ordered it. My husband replaced the part easily. The microwave work very well.The microwave was to our friend. He did replace it by a new one. Now we have a new microwave with a fan.
Was this instruction helpful to you?
Thank you for voting!