YWMH53521HW05 Whirlpool Microwave - Instructions

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

Put s pot under were you take the screw out.If you drop it you can get it easy

I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

Followed instruction already on your website

Replaced both filters

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

I measured. I leveled. I mounted hanging bracket and here's where it got tricky because you need two people to raise the microwave into position. I'd stack 2x4's In the back by the wall. I'd stackem in the front on the cabinet top then raise the back and add more. You get it front back front back until it's high enough to snag the bracket. Holes pre drilled raise it on up tighten bolts and poof you're done!! I did loosen the screws that pull the cabinets together and the bottom screw that holes the cabinet on one side. It didn't seem like it needed it the way it slipped in but maybe it slipped in because I did it. Only takes a minute. Use a minute here save an hour there. Go do it! Times a wastin!!

Used a screwdriver only. The grill vent is not at all durable and stared to crack. The microwave is less than 2 years old.

Remove top grill screws [2] remove grill replace filter put back together.

Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.

Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.

I first unplugged the microwave. I then unscrewed the 2 screws from the top grill. I had to be careful because the grill was cracked close to each screw. It was a little tricky to remove the grill. Had to tilt it down as I removed it, and make sure the microwave door was opened as wide as possible. Filters were placed as the old ones, with the metal part up I believe. A little tricky to get one of the filters to fit. Grill was replaced with care so as not to further Crack it. Kind of maneuvered grill back in place, getting right side in place first. I noticed there were several tabs on the grill that needed to be placed inside of the microwave body while reinstalling the grill. Once the grill was in place, the 2 screws were put in to hold the grill in place.

mounted bracket, case closed.

We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.

Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.