MH1170XSS1 Whirlpool Microwave - Instructions

Replaced light bulb.

Uncrewed existing screws. Slipped on new vent tighten screws finished

I ordered bulb, which was stuck in socket. Order a new bulb amd socket, now is working fine thank you for your help and having the part we needed, it was delivered in a couple of day and now is working

Had to take all the screws out of the bottom of the microwave to get to the socket. Once that was done, it was a simple fix of taking out 2 screws that hold the socket in, and then unplugging it. Replug and put all screws back. It was a fairly simple fix for the diy homeowner.

1. Safely unplug the dryer. 2. Unconnect the vent hose. 3. Pull it out so you can have room to move around to work on it. I actually in a power chair so I put an old blanket on the floor and laid it face down to work on it. It was extremely dirty so I used a shop vac to clean off the back panel before starting. 4. I took off all the screws and cord cover with a nut driver, used the shop vac again to clean the entire inside. Properly a 1/2 to 1 inch of dust and lint was built up causing a dangerous fire situation for sure. Once clean, take a photos especially of where the electrical connection are. 5 Located and removed the two screws holding the element on, used a nut driver and long nose pliers to remove the heat sensor & electrical connections. 6. Dry fit the element before tightening screws to make sure placement is correct then match the holes replace the screws. 7. Using the photos put the heat sensor & electrial wires back on, you may need to use the pliers to push it on tight. Double check everything, clean back panel inside and out, match up holes replace screws, I actually checked my power cords screws for tightness then replaced cord cover. 8. Replace vent hose if needed or then reattach it and plug it up. You may need to check the dryer barrel by turning the drum around a few times. Should work perfect, you will smell the element a little but it should be ok. Remember clean your dryer inside and out every six months or so to prevent dryer fires.

I had to hammer out the broken star wrench tip then progressively drill the head off of the bolt. Once accomplished I could remove the door. I used a standard replacement screw I case I ever have to replace the door again. The manufacturer should use a fastener other than a star head bolt.

The filter was just a maintenance issue. The vent grille, as described on the website already, is poorly constructed; the plastic where the screws attach to hold it on break easily. I ended up using something similar to the plastic of a credit card to make a repair to the side that had broken. I ended up not installing the new grille, I thought I would see how the repair I made held up first. I kept the grille as a spare when the old one finally breaks. CAUTION: When you clean the grille, take it off first! The two spots where it attaches are cheaply made and will break easily. Take out the two screws, clean the grille, and then put it back into place. DO NOT OVER TIGHTEN THE SCREWS! Tighten them just enough to hold it in place.

The repair was very simple. only had to remove two screws and replaced the broken grill.

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

replaced burnt parts

Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.

You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.

My daugher used the vent grill on the microwave as a handhold while putting dishes away in the cupboard and broke it. I found the part via the Whirlpool website. When the part arrived I removed the two screws, placed the new vent grill in place and replaced the screws. Total time: About 10 minutes.

Watched video which reminded me to order support for the turntable support ring and did exactly what the person in the video did. Excellent and prompt service and all parts fit.

After researching online, I found that I needed the turntable drive coupling, part#PS993087. when I went to your site it showed the same part but the part number had changed but said it would fit my microwave. Well, I was really surprised and happy when the part I received 3 days after I placed the order, with normal shipping,fit perfectly and now my turn table in my microwave works. I have marked this site a a favorite and will use it I'm sure soon. Being a single women and having to figure out how to fix the things on a small buget, I'm learning a lot and have a lot of respect for men that know how to do all the repair stuff. Thanks so much, I have been able to mark this off my list of things to fix. Have a nice day. Cj- age, 58