GH6208XRS0 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jennifer from Red Oak, IA
- Parts Used:
- 8204670
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light burned
Unscrewed the lens cover anbd inserted the new bulb. Put the cover back on and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Anoka, MN
- Parts Used:
- 8204670
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out overhead light
Some difficulty getting screw loosened, once that was done replaced burned out bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Edwards, MO
- Parts Used:
- W10244764
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
handle on door broken
remove screws from the door trim remove two screws from the handle and replace with new found out the handle is directional had to remove and reinstale in right direction reinstae the screws for the door trim
Was this instruction helpful to you?
Thank you for voting!
glass plate broken, turntable driver melter
replaced the above and t. ring, spacer and motor. from underneath the microwave, two screws lets motore drop down, then detach two wires from terminals on moter (be sure to unplug the microwave first) and from insdie the microwave the driver pulls up off the motor shaft easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Eugene, OR
- Parts Used:
- 8205994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable Driver was down to two legs . . . one had melted into a blob!
I removed the injured turntable driver . . . had lost one of its three legs due to some sort of uber-thermal meltdown! As a result, the microwave turntable was turning a bit, stopping, turning a bit more, stopping . . . I was concerned I wouldn't be able to find such a tiny little part, but voila . . . PartSelect had what I needed. Other than the cost (it's just a tiny piece of plastic!) and s/h . . . I'm happy to have a fully functional microwave back! I simply popped the new turntable driver into place and replaced the glass turntable and plastic ring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from payson, AZ
- Parts Used:
- W10120840A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
need new filter
replaced old filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Hanahan, SC
- Parts Used:
- W10120840A, W10120839A, 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bulb Finally went out
Used an apex bit unscrewed the fittingand down came the light cover. Pulled the old bulb out and had to use a flashlight to line the prongs up to install the new one. Whileeverything was down used an oven cleaner to degrease and clean EVERYTHING. You wouldn't beleive how much grease and debris will accumulate in 5 years. And I only fry bacon once in a blue moon. All in all it was simple to order, clean, and repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoEllen from Salinas, CA
- Parts Used:
- 8205992
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke the glass turn table tray in my microwave
There was no installation involved. I just placed the new tray in my microwave. What is amazing however, is I ordered my part early one morning, the tray arrived at my door step the next day.I paid for regular shipping. Thanks guys good work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Biviana from Sunrise, FL
- Parts Used:
- 8206123
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door handle
Remove top and botto screws, then use a butter knife to pull apart the door and remove the handle screws. Replace new handle ,make sure the little plastic ring inside screws are properly place in order to be able to screw the new handle back. And there,you have your new fixed appliance!! Easy cheese! ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dotty from Hillsboro, WI
- Parts Used:
- 8204670
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
surface light on microwave wasnt' working
took the light assembly off and replaced the bulb and put the assembly together and fitted back in the space and finished the assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Rock Island, IL
- Parts Used:
- W11661547
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy turntable motor
Unplug microwave. Remove turntable and support from inside. Remove outside bottom cover (10 screws). Remove 2 torx screws holding motor in place. Remove 2 wires from motor, noting colors. Wires are held with spade connectors that has a small tab that needs to be depressed. Remove washer from motor and place on new motor. Entire procedure very easy.
Was this instruction helpful to you?
Thank you for voting!