YMH7155XMS2 Whirlpool Microwave - Instructions

Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.

I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock

Had left the small break in the handle go too long, There fore the screw holes in the door had wallowed out. Had to put some small washers in to bridge the wallowed out screw hole. The ends of the handle had broken off on the end of the mounting screws, had to use pliers and the screwdriver to get the plastic mounts off. There was enough room for the washers so no additional adaptation was needed. It all went back together very easily.

After taking the three screws out of the side of the door, I actually had to get help from my Dad who came over and was able to pry the top corner of the door out of the casing. I was afraid I was going to break the door. Once he got the door pried apart, I was able to replace the handle, clean the entire door and quickly snap it back into place and then replaced the screws.

Removed bed two screw replace grill

It's a simple repair but costly. Just open the door remove the three screws on the side of door. Now use a small screw driver or metal putty knife to remove the chooker collar around the door " be careful this can easly be broken". Okay now the metal inner door is easier to remove if you slightly bend the tabs up around the door. Look carefully you should be able to see where they catch. Once you do that carefully seperate the outter door cover. Careful sometimes it will pop right out and fall. Please no more further repairs needed. Just screw in the new handle push tabs back out on the metal inner door then snap everything back together and reinstall the three screws.

Unscrewed 4 different screws, replaced the vent & returned screws. Ack to original positions

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.

used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts

It took me time to remove the parts and suss out the issue, but the repair itself was EASY. A wire ribbon connected to the circuit board had gone bad. One Phillips head screwdriver, 7 screws, to get at the old one, pull it out, replace it with the newly ordered part. NO PROBLEM. Ladies, you can do IT!! You have the power!

Bought a new one. Perfect match, easy replacement.

Didn't realize this part had two tabs with reinforced screwholes in it. Those obviously had snapped off at some time in the distant past, and I had always removed the grille for cleaning carefully and washed it by hand and replaced it. The clean freak moved in and took this out WEEKLY and all the other tabs were eventually cracked and made the grille unusable; it kept rattling and falling out. When I got the replacement I noticed the broken tabs and replaced the item in a few minutes after removing the debris of five or six tabs and finding a Philips head screwdriver for the apparent screws (in fine shape, they were!) and tab remnants. Good fit, looks like new. Now hopefully the clean freak won't find my screwdriver next week.

Very easy to replace. A short ladder provides easy access to two small Phillips screws on the top of the existing grill.
Remove and keep these screws to re-use.
Remove old cover and discard.
Fit tabs on the bottom of the new cover into position on microwave and press entire cover securely in place matching the screw holes to the existing microwave.
Replace small Phillips screws securely.
Step back and admire your microwave!

Placed to new grille on the microwave and attached
with the screws.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.