MH3184XPT2 Whirlpool Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Foreclosed home: parts were missing
Having the correct model number helps:
Just place the parts in the microwave and it worked.
Just place the parts in the microwave and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Wilson, NY
- Parts Used:
- 8205146A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
New Home and builders did not install the filter.
Part was easy to order on a secure site. The filter will make a difference as our appliance is not externally vented.
Good people to deal with.
Good people to deal with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Parkesburg, PA
- Parts Used:
- W10450187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
top snapped off top of micro wave
Snapped it back on. However, I made a mistake and ordered the wrong color. You wree great, shipped the right one the same day, and took the other one back.Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Vallejo, CA
- Parts Used:
- W10450172
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken clips on two hood-microwaves- one at home one at a rental
The two repair items were exactly right and just snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfred from summerville, SC
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt Out Light Bulb Replacement
Open compartment, installed bulb, closed compartment
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from SPRINGFIELD, WV
- Parts Used:
- W11707984
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Maceo, KY
- Parts Used:
- 8169438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The microwave door would not stay latched, so it wouldn't come on.
The repair was easy, I just took off a few screws and found the broken latch spring. The real story is how easy it was to find the replacement spring from Partselect! I couldn't believe they had it, and even better yet, I ordered it one afternoon, and it came the next day with normal shipping! Unbelievable! Then I just popped it in and replaced the covers I had removed and it was working again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amber from Loretto, PA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass tray in the microwave got chipped while i was washing it and started to crack.
I just opened the box and set it in. Took all of two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Statham, GA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement
Easy, perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugenio from San Jose, CA
- Parts Used:
- W10450172
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken clips and plastic pieces holding tabs
The only to repair the vent grill was to purchase a new one. I went ahead and found a the replacement part and waited 5 days when it arrived. Very easy installation. Ijust lined it uap amd popped it in place. With a screwdriver I made sure to extend the clips slightly to ensure they fit snuggly to ensure they held the vent tightly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from White House, TN
- Parts Used:
- W10450187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Vent/Grill cover
Received new cover the next day. Snapped new cover in place with no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Grapevine, TX
- Parts Used:
- W10450187
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Vent Grille clips broke off
Snap the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JASON from ABSECON, NJ
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plate
Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Huntington Beach, CA
- Parts Used:
- 8184581
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Microwave was making a grinding sound
Problem was easily diagnosed using the internet as a resource, problem was a bad stirrer motor. Hardest part of the repair was the removal of the microwave. Once off the wall, you remove the outer cover and a molded plastic casing directly underneath the outer cover at the top of hte microwave to expose the stirrer motor. Removed two screws and two wires and the old motor is out. Did exactly the opposite to install the new motor. The kit I recvd included among other things the motor, a new inside cover, plastic rivets and even silicone to seal the inside cover. I am sure I saved a couple hundred dollars by doing myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Mesquite, TX
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb burned out
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Was this instruction helpful to you?
Thank you for voting!