MHE14XMB1 Roper Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Norma G. from Poinciana, FL
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The vent grill was broken
I remove the old broken Grill Vent by loosing two screws and just put the new one and adjusted with the same two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DIANA from BORDEN, IN
- Parts Used:
- 8183851
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plastic tabs broke and the grille fell off.
Removed the screws holding the broken tabs and thought the new vent grille would click right into place. I had quite a bit of trouble getting all the tabs lined up to click into place, but was finally able to do it. Then I just used the old screws to secure the new grille.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Palm Harbor, FL
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
vent grill broken at installation screw
old vent off screwed new in less than a minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Tucson, AZ
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Vent grille tabs were broken
Replaced it with a new vent grill simply by screwing in on. It works and looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Sonora, CA
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Vent grill on my microwave broke
I was in a panic as no one in our twon had this part. I found PartSelect online and ordered the part. I ordered this part at 4PM and the next day at 2PM the part was at my house. My husband spent 30 seconds screwing it back on and it looks like new. I can't say enough wonderful things about your Company and Customer Service!!! You're the BEST!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HARKER HTS, TX
- Parts Used:
- W11707984
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Microwave had no electrical
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Was this instruction helpful to you?
Thank you for voting!
Foreclosed home: parts were missing
Having the correct model number helps:
Just place the parts in the microwave and it worked.
Just place the parts in the microwave and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sadagopan from Frisco, TX
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Vent grill was broken
Just remove the old one, inserted the new grill and tightened the screws on the top of the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Eureka, CA
- Parts Used:
- 8183851
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave grill broken...
Unscrewed existing screws, removed old grill, fit new grill into proper slots, reinstalled and tightened screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfred from summerville, SC
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt Out Light Bulb Replacement
Open compartment, installed bulb, closed compartment
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herb from Auburn, IN
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
it was working fine and it stopped order a fuse and it wasn't the problem
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Edwards, CO
- Parts Used:
- 4393777
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door cracked and the door handle fell off.
I removed the screws to the old handle and screwed on the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Maceo, KY
- Parts Used:
- 8169438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The microwave door would not stay latched, so it wouldn't come on.
The repair was easy, I just took off a few screws and found the broken latch spring. The real story is how easy it was to find the replacement spring from Partselect! I couldn't believe they had it, and even better yet, I ordered it one afternoon, and it came the next day with normal shipping! Unbelievable! Then I just popped it in and replaced the covers I had removed and it was working again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from SPRINGFIELD, WV
- Parts Used:
- W11707984
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larrt from Minooka, IL
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Was this instruction helpful to you?
Thank you for voting!