MHE14XMQ0 Roper Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from HOLLY LK RNCH, TX
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Clips on grill broke
Removed bed two screw replace grill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Smithtown, NY
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
machine was dead.
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from ORANGE, CA
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mouang from Sacramento, CA
- Parts Used:
- 4393799
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Glass tray shattered
Ordered the glass tray and installed it. Received the orderin about two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from Charleston, SC
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
"Lost" microwave tray
Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Basehor, KS
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
grill mounting braket broke
The part came very quick less than a week. The installation took less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael J from LORAIN, OH
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb which lit the surface of the range.
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.
Was this instruction helpful to you?
Thank you for voting!
Glass tray missing and vent grille broken
Replaced the missing tray and unscrewed a couple of screws to remove broken grille tabs and retightened the screws to hold in the new grille. Very successful and very easy. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Henderson, NV
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cooking tray chipped
replaced with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin King from Silver City, NM
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass plate of Microwave missing from an in bulit microwave
Glass plate arrived in less than two days. Placed the glass plate in Microwave and presto the microwave works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- barbara from phoenixville, PA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turntable in microwave cracked in half while cooking
submitted manufacturer info to website and voila! a new glass turntable arrived in 2 days. I don't do well with computers, my 23 yr. old daughter was impressed......couldn't be easier! thanx! will definitely revisit your site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jaime from Melbourne, FL
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Vent Grill
Removed screws holding tabs from broken vent grill to microwave frame.
Carefully snapped new grill vent into slots on top of microwave and slid tabs into slots on top of the frame.
Replaced the two screws in the tabs.
Finished
Carefully snapped new grill vent into slots on top of microwave and slid tabs into slots on top of the frame.
Replaced the two screws in the tabs.
Finished
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from ROGERSVILLE, AL
- Parts Used:
- 8183948
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
vent grill tabs broke off
took old vent grill and tabs off using phillip screwdriver. started putting new grill on and it wouldnt go on. got to looking and there are two more screws that you have to loosen up so the grill will go into place these two screws are between the two tabs at each end. caution do not over tighten the screws it will break the tabs. overall easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from Baltimore, MD
- Parts Used:
- 8183948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Vent grill wouldn't stay on. The clips broke.
Take out the screws, broken pieces of clip, then put in the new vent grill, replace the screws. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benita from Port Orange, FL
- Parts Used:
- 8183851
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
vent grille was knocked loosesomehow. allthe holes for the screws were broken
Removed the screws from the damaged sections and replaced the new vent grille. Less than 5 minute fix, and saved me over a 100 dollars according to the quote I got. Thanks
Was this instruction helpful to you?
Thank you for voting!