MMW9730AB00 Maytag Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- dan from Gallatin, TN
- Parts Used:
- WP74008369
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
oven had error messages
I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.
After that it was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from BUCKEYE, AZ
- Parts Used:
- W11718046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
wanted racks that were more stable
removed existing racks; slide new rack over both sides to the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J.M. from Royal, AR
- Parts Used:
- WPW10618107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Inner door glass EXPLODED while preheating!
Easy peasy. After using the shop vac to remove the glass fragments, 8 Phillips head screws were all that I had to remove. The schematic on this website was close enough, but I recommend taking pictures as you disassemble.
Caveat: I took it apart several days before I got the part, so I had plenty of time for my forgetter to work.
Caveat: I took it apart several days before I got the part, so I had plenty of time for my forgetter to work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from WALTON, KY
- Parts Used:
- W10886919
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
INTERIOR OVEN LIGHT
EASILY REMOVED GLASS COVER INSIDE OVEN AND REMOVED SMALL HALOGEN LIGHT BULB.
RECEIVED REPLACED WITHIN TWO DAYS OF ORDER AND REPLACED BULB AND GLASS COVER IN ABOUT 10 MINUTES.
MOST DIFFICULTY WAS HAVING TO BEND DOWN TO REACH INSIDE OF OVEN TO LOCATE POSITION TO INSERT BULB.
RECEIVED REPLACED WITHIN TWO DAYS OF ORDER AND REPLACED BULB AND GLASS COVER IN ABOUT 10 MINUTES.
MOST DIFFICULTY WAS HAVING TO BEND DOWN TO REACH INSIDE OF OVEN TO LOCATE POSITION TO INSERT BULB.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MIAMI, FL
- Parts Used:
- W10660052
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Micro Wave Steamer
I spoke to Daily via the phone and I ordered a new steamer since my original steamer cracked over a period of time. No installation, no problems I just recently used it and works perfectly! Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Carrollton, TX
- Parts Used:
- W10915651
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Part worn out
Could not complete the repair due to broken part when arrived. Reached out to service department but have not heard back. Maybe email did not go through due to pictures attached of part condition once arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Ladson, SC
- Parts Used:
- W11193483
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The light in our microwave was out.
We had to remove screws from the vent covers above and below the microwave, then there were 2 screws (one on each side) that attached the microwave to the oven. Once all of the screws were removed we had to pull the microwave out. Then we pulled the light cord out, removed the burnt out light and installed the new one. Then reversed the steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Scranton, KS
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from las vegas, NV
- Parts Used:
- W11110134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace spindle on turning table
exact part in with the new out with the old
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from TRENTON, MI
- Parts Used:
- W10886919
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light burnt out
Took off outer cover Popped out old bulb put in new one
Replaced cover
Replaced cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Chicago, IL
- Parts Used:
- W11718046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Decided to replace the stationary racks with rolling racks
To my amazement, they got here overnight. We unboxed them and put them in. Doesn't get any easier than that. Now all of the racks in my double oven are super easy to use when cooking. Wish you made rolling racks for the gas stoves (unfortunately, the ones for the double ovens were too big for the gas oven).Thank you
Was this instruction helpful to you?
Thank you for voting!