MMV6186WB0 Maytag Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Meridian, MS
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Charcoal Filter Replacement
This is an under the counter microwave. Simply removed the two screws holidng the vent grille on top of the unit, lift out the old charcoal filter, clean the vent fan exit surfaces then replace the filter and put the vent grille back. Be careful to not drop either of the two screws after one is installed as you will have to take the grill off and start the screw installation again unless you have a magnetic to retrieve the dropped screw. An easy five minutes at most to change.
Was this instruction helpful to you?
Thank you for voting!
Foreclosed home: parts were missing
Having the correct model number helps:
Just place the parts in the microwave and it worked.
Just place the parts in the microwave and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herb from Auburn, IN
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
it was working fine and it stopped order a fuse and it wasn't the problem
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfred from summerville, SC
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt Out Light Bulb Replacement
Open compartment, installed bulb, closed compartment
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from SPRINGFIELD, WV
- Parts Used:
- W11707984
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amber from Loretto, PA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass tray in the microwave got chipped while i was washing it and started to crack.
I just opened the box and set it in. Took all of two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Statham, GA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement
Easy, perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Oakland, NJ
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
changed filters
Replaced filter which came inrecord time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JASON from ABSECON, NJ
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plate
Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Cranston, RI
- Parts Used:
- W10208631A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
replace filter
slide into place under hood
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Mesquite, TX
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb burned out
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carter from McCordsville, IN
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burn't out bulb.
Removed the glass cover and replaced the bulb. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from New Berlin, WI
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Clearing the clean code was the hardest part.
I had no problem installing the new filter. Just used a phillips screw driver to remove the two screws holding the vent cover in place. Cleaned the dust out of the ducts and reinstalled the new filter. The screws must be held to the screw driver with your finger tips so you don't drop them in the vent cover. The most difficulty I had was in clearing the clean code from the screen. There are no instructions in the owners manual for doing this. But after several tries I got it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Denver, CO
- Parts Used:
- W10208631A, 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Filter dirty
I unscrewed the filter cover, replaced the charcoal filter and replace the cover. The other wire mesh filter slides right into place. You sent me the right parts for my filter replacement on my microwave. Easy install. Thanks
Was this instruction helpful to you?
Thank you for voting!