MMV5208WW1 Maytag Microwave - Instructions

when I opened the back cover of microwave, the diode was kind of blackish blown, since there was light bulb and fan were still working, i thought it could be problem with any one of the components like; magnatron or capacitor or diode, so first replaced the diode and mica at the end of the magnatron duct, there was problem with door switch as well. i fixed that too. Now it is working. It cooks bit faster, Wondering why?

This is an under the counter microwave. Simply removed the two screws holidng the vent grille on top of the unit, lift out the old charcoal filter, clean the vent fan exit surfaces then replace the filter and put the vent grille back. Be careful to not drop either of the two screws after one is installed as you will have to take the grill off and start the screw installation again unless you have a magnetic to retrieve the dropped screw. An easy five minutes at most to change.

I would like to thank these guys ...First of all very good customer service , i gave them the model number of my microwave and right there they have the parts for me . And they delivered my item right the next day though i ordered it late afternoon. The installation is so easy not a sweat , and i installed the parts like less than 5 minutes. Special thanks to the guy who helps me to Gordon B. Very nice Customer Service Representative. Thanks Ariel

took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse

Open compartment, installed bulb, closed compartment

Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!

Replaced filter which came inrecord time.

I unscrewed the filter cover, replaced the charcoal filter and replace the cover. The other wire mesh filter slides right into place. You sent me the right parts for my filter replacement on my microwave. Easy install. Thanks

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

slide into place under hood

You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.

But something dirrect on the glass it was cold and when the microwave stopped the glass broke. Got on the internet order a new glass on Sat. it was shipped on Monday and we received it on Friday. Thank you for your great service.

Replaced light bulb.

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

This is an over stove top mounted oven. Remove oven from mount and place on a work surface with padding to support the lamps and vent holes. Strip the case off and locate the noted other "most likely" parts. Watch out for the Capasitor. Read the test note available for each part; Diode, Thermister Fix, Capasitor and Magnitron. Do the test checks. My issue wasn't obvious because I think the Capasitor was discharged and needed to be hot to check the Magnitron. (I'm not an electrical engineer so...) At this point I did the foolish thing...I plugged the unit in and ran it. Watching from a distance I saw sparks fly from the top side of the Magnitron with the same result from my cup of water (cold-no sprks here.) I replaced the diode and tried again, same result. I ordered the Mag and the Thrmst-Fix. Thrmst-Fix was on BO when the Mag got here so I installed the part. Had to remove several pieces to afford room to work and still had to stretch and pry to get the old out and new in. Mag is held in place with Torx screws so check that before you start. No other tool works. Mag was the problem for this unit. Some problems encountered: Parts and pieces were quick in arriving as long as they were not Back Ordered. Be careful to follow a thread for your product to order parts. These review/instructions are mixed for simular appliances and sometimes lead off to other part lists and numbers. Prices differ from model to model, list to list and the part numbers change. Go back to your product and then trace for the correct parts. I noted a $40 price dif.between Magnitrons from simular part lists. When you receive the part check to match the part numbers, Manuf. no. are different from the Part Select No. but can be crossed. Otherwise using this site's instructions, checks, insulated tools, big rubber gloves and a face shield I managed to save a $600 machine from the junk pile. Parts as ordered were recieved and return of un-touched parts were accepted by Parts Select without unexpected hassle. Thanks for a positive experience.