UMV1152BAS Maytag Microwave - Instructions

It literally took me longer to unpackage the fuse than to install it. I removed the outer shell by unscrewing the five screws, lifted it off and set it aside. The old fuse was readily visible so I pulled it out and put the new one in its place. I set the shell back on and replaced the screws. I plugged it in and ran it for 30 seconds while still in the shop just to make sure that solved the problem and presto - it worked like a charm. A $20 part saved me from having to purchase a new microwave (sadly, I had to break the news to the wife).

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.

My wife was pushing a few buttons with her knuckle (hands were full)and the microwave just turned off. Just like we had blown a breaker. First I unpluged it. Then I removed the phillips screws of the front panel, and found and removed the ceramic fuse. 3 days later I received the new fuse in the mail, and put it in. I plugged the microwave back in and it works great.

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

Replaced the diode (aka wire-vltge) in the HV circuit after removing cabinet cover using both the secure torx screw drvr & phillips head screw drvr. The hardest part of the job was finding the secure torx nut drvr tool on the internet & purchasing same.

Replaced light bulb.

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

Due to the way the appliance was installed, it was impossible to get to the outer vent grille mounting screws. My husband was finally able to pry the grille cover off with a screwdriver. I was finally able to clean the grille cover and replace the filter. The grille cover no longer fits as tightly as it should because part of it broke off, but it will do. The builder did not consider maintenance when installing the appliance.

The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

First let me say that I tried several places to get what I thought was a simple light bulb. This included several national hardware stores as well as a national electrical supply company. No luck. Went to the manual and PartSelect. Not only did you have it in stock, ship right away,at a reasonable price it arrived in a matter of days. One would not normally think of receiving a "how to" video to change a light bulb but you did. That impressed me. Suffice to say the replacement went well and you can be certain the next time I need a part I will go to you first. I am also impressed with the organizations with which you are affiliated with. BBB, Norton, PayPal, money back guarantee etc. Thank You The entire process was made pleasant with your support.

I simply went on line to Part Select, placed my order, made payment, and was astonished to see the package with a new dish sitting on my doorstep the next day.Great service.