Models > MT1044BB > Instructions

MT1044BB Maytag Microwave - Instructions

Jump to:

All Instructions for the MT1044BB
16 - 30 of 31
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mark from GREENSBURG, PA
Parts Used:
WPR9800486
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
microwave not heating
removed a dozen screws-discarded large cap-replaced diode-replaced a dozen screws(took longer to replace them than remove for some unknown reason). Microwave now works(wife happy).
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from CALIFORNIA, KY
Parts Used:
WPM0805101
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
No power to any microwave functions
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jason from WASHINGTON, IN
Parts Used:
DE92-90189S
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Missing roller guide under glass plate
I used my pocket knife to open the package. I opened the door and removed the plate and set the guide down and put the glass plate back.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Lake Havasu City, AZ
Parts Used:
DE31-10170C
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Rotate motor for Micrwave turntable failed
Turn off power to microwave (kitchen circuit breaker) Remove 3 sheet metal screws bottom front, disconnect electrical connections to motor and lights, remove defective motor(1 screw), replace with new unit, replace screw, re-attach bottom (3) screws, test. Replacement motor cost via this supplier was 1/3 of what local appliance repair store would have charged.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
SUSAN from ALDEN, NY
Parts Used:
DE74-20015G
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Glass Tray For Microwave
Set it in the oven, wonderful!!!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
SUSAN from DAVISON, MI
Parts Used:
DE60-30016A
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench set
upper fan motor bad
My repair went terrible as I was sent the wrong motor 2 times. My stove sat in the middle of my small kitchen for 2 weeks. Finally the 3rd was the correct one except I didn't have the right nut so I waited another day for that to be sent. Everything working good now, I just hope the bottom fan doesn't go out after this experience.
1 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Muhammad from Jersey City, NJ
Parts Used:
WPR9800486
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
No Heating.
Information provided on the web site by Part Select, were helpful and encouraging to select and buy the part needed to repair the appliance. No doubt, a skilled person having background in the repair of appliances should attend such repair job.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOE from CENTERREACH, NY
Parts Used:
DE47-20009A, WPM0805101
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
no power to unit after replacing fuse
went to you tube and found a segment compatible to my issue.called the web site and ordered the thermostat fuse and ceramic fuse in case i had the wrong one purchased at the locale H/Depot. The only issue was I did not know that there was 2 different thermo fuses,,one controls fan and the other a basic one. luckily the fan wasn't the one that was blown.The woman i spoke to was very helpful and my order was AT MY HOUSE in less then 24 hours.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Yanet from Coral Springs, FL
Parts Used:
DE74-20015G
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Glass tray broken
Simple replace
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clifton C from Kingsland, TX
Parts Used:
4713-001102
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Bulb out
Pretty easy tear down and assembly once I removed it from cabinet (built in micro)
Was this instruction helpful to you?
Thank you for voting!
Customer:
outstanding from Galena, MD
Parts Used:
WPR9800486
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
microwave would not heat.
hardest part was taking the microwave down off of the wall to gain access to the diode. Thought if was the transformer but ended up being just a blown diode. remove and replace and bench test. that part took 15 minutes . moral of the story don't boil water under the side of the microwave that holds the electric components.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MT1044BB
16 - 30 of 31