JMV9196CS5 Maytag Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from WEST NYACK, NY
- Parts Used:
- WPW10466420, W10337248
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable Motor burned out
Unplug microwave
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet
r
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet
r
Was this instruction helpful to you?
Thank you for voting!
Wrong mounting plate
Two Mounting plates # PS12074431 were sent to me and both do not fit.
Model number MMV1175JZ-0
Serial number TRX-17. 24546
Manufactured April 2020
Contacted Maytag and even sent pictures to show the problem with alignment of the mounting plate not fit in the back of the microwave.
Model number MMV1175JZ-0
Serial number TRX-17. 24546
Manufactured April 2020
Contacted Maytag and even sent pictures to show the problem with alignment of the mounting plate not fit in the back of the microwave.
Was this instruction helpful to you?
Thank you for voting!
I had a cabinet person install new kitchen cabinets and counter top. After the demolition of the the old cabinets, I had to buy new parts for the new instal
I had the help of a handyman, I'm 75 years young but not handy with tools
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from SUFFERN, NY
- Parts Used:
- W10709921
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb under the microwave burned out
Used a philips head screwdriver to remove one screw holding the light cover. Pulled out the old bulb and inserted the new one. Replaced the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from CARBON HILL, AL
- Parts Used:
- W10337248
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic piece that spins turntable failed because of prolonged heat, I suppose.
Just opened the door and dropped in new part and viola!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CARMELO from LOVETTSVILLE, VA
- Parts Used:
- W10709921
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both lights failed. Replaced with new bulbs.
Unscrew lens and direct access to surface light cavity. Removed old light bulbs and replaced with new bulbs. Reassembled lens cover and turned lights on successfully. Took less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from TAMPA, FL
- Parts Used:
- W11402532
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass turntable tray was chipped
Removed the old turntable tray, replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabra from PEACHTREE CTY, GA
- Parts Used:
- W10337248
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Brand new (open box) purchase from a local appliance liquidator had missing drive coupling. This part holds the glass plate in place and allows it to turn.
It was a very simple and easy fix, no tools needed. First, open the door to the microwave/oven and remove the glass plate and the plastic plate guide. Next, locate the whole in the center. Using your finger, find the drive coupling pin that sits just below the opening (half circle shape). Align the bottom of the drive coupling with the metal pin and press down. Replace the plate guide and plate. The grooves in the bottom of the glass plate should be aligned with the shape of the drive coupling. Test by setting microwave/oven to 30 seconds and watch for proper turning and alignment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BURNSVILLE, NC
- Parts Used:
- W11402532
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broke thw carosel plate
took it out of box wooolaaa fixed thanks fast shipping too...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from brockton, MA
- Parts Used:
- W10709921
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I noticed that the hood lights were out.
I took off the glass panel underneath the microwave and replaced the 2 bulbs in less than 3 minutes by myself with only a phillips head screwdriver. I was very pleased with the service I received and more pleased with myself that I did not have to call in a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Smithtown, NY
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
machine was dead.
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from BILLINGS, MT
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced the charcoal filter.
On top front of the microwave are two Philip's head screws holding the rail on. Remove these screws and the rail snap out the old filter (noting the dark side down) then snapping the new filter in. Replace rail. 10 to 15 minute task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from GLIDDEN, WI
- Parts Used:
- W11025649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mounting plate support edge broken
I removed the microwave to install a back splash and found the support edge on the backplate had broken off and was missing. I searched for parts for the microwave and found them on PartsSelect.com. Easy to order, and was shipped promptly.
Once the part arrived, install was simple, lining up the existing holes. The only hard part was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.
Overall a very simple repair.
Once the part arrived, install was simple, lining up the existing holes. The only hard part was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.
Overall a very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard L from PRESCOTT VLY, AZ
- Parts Used:
- 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Charcoal Filter getting old, needed replaced
Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.
Was this instruction helpful to you?
Thank you for voting!
On Turning on the Microwave, it was sparking, was not sure where the sparks are coming from, initially I thought mica at the end of megnatron duct could be the issue
when I opened the back cover of microwave, the diode was kind of blackish blown, since there was light bulb and fan were still working, i thought it could be problem with any one of the components like; magnatron or capacitor or diode, so first replaced the diode and mica at the end of the magnatron duct, there was problem with door switch as well. i fixed that too. Now it is working. It cooks bit faster, Wondering why?
Was this instruction helpful to you?
Thank you for voting!