LMV1680BB LG Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from RICHMOND HTS, OH
- Parts Used:
- 6549W1S013K, 4370W1A006B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Was making a noise when turning around
I removed the bottom plate which had 9 screws.
than unplug 2 wires to the motor and unscrewed 2 screws, replaced the old motor with the new one and also the coupler. and so far no noise. easy fix. Thanks
than unplug 2 wires to the motor and unscrewed 2 screws, replaced the old motor with the new one and also the coupler. and so far no noise. easy fix. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SEVERN, MD
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
food does not get hot, carousel did not turn, all other indicators worked
Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vic from Allen, TX
- Parts Used:
- 6600W1K001D, 6600W1K001C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When the MW door was opened a fan would start running. Close the door the fan would go off.
Removed the MW from the wall. Took the top screws off the air vent. Then removed the two screws holding on the display. I then moved the display to its side and it revealed the micro switches. I removed the plug in leads from the micro switch one at a time. I did this with all three micro switches only one at a time. I reinstalled everything and plugged it in. No more fans starting when the door is opened.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from ORCHARD PARK, NY
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door switch was burnt out
Removed outer cover
removed lower door switch
installed new switch
Wa La!
removed lower door switch
installed new switch
Wa La!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from EL DORADO, KS
- Parts Used:
- 5230W1A011B
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
UNABLE TO INSTALL DUE TO DAMAGED IN SHIPPING
WORTHLESS...I EMAILED YOU ON 2/7/22 AFTER RECEIVING THE DAMAGED FILTER DUE TO NOT SHIPPING IN A HARD OR SOMETHING IN THE ENVELOPE TO PROTECT THE FILTER FROM BEING BENT.
I HAVE NOT HAD ANY RESPONSE FROM YOU FOR THE DAMAGED FILTER OR WHEN I CAN EXPECT ONE THAT I CAN USE.
UNSATISIFACTORY SERVICE!
I HAVE NOT HAD ANY RESPONSE FROM YOU FOR THE DAMAGED FILTER OR WHEN I CAN EXPECT ONE THAT I CAN USE.
UNSATISIFACTORY SERVICE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from DEPEW, NY
- Parts Used:
- 3B73362F
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not start when closing door.
Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from DELAND, FL
- Parts Used:
- 4026W2A019C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave door would not shut completely and would not activate switches
After checking all three switches for continuity I determined that the plastic door lever had warped or gone out of wack. After shutting off power at the breaker box I removed the door, the inside trim piece around the inside of the glass. Removed the black two prong door lever, reattached the new door lever and then reinstalled the trim piece and all screws. Works fine now. Easy fix just make sure your switches are all ok then replace the door lever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joy from PRESCOTT, MI
- Parts Used:
- ADC49436905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door cracked at bottom of handle
Replaced whole door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from CRYSTAL LAKE, IL
- Parts Used:
- 3B73362F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Items were not getting heated up in the microwave,
I went to LG website enter model number and was given a list of parts that need to be replaced with a percentage of which part fails the most. I order micro switch PS3522738 which arrived and PS3529293 was backordered. I installed the one that arrived. The microwave worked briefly. I reordered and waited for both switches to arrive and installed both. The microwave still doesn't work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suresh from RESTON, VA
- Parts Used:
- MEB41908102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Hard to take out old screws.
Self
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from TAMARAC, FL
- Parts Used:
- 3550W1A126D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
did not include screw to secure it to celing of the microwave rempved
removed old cover put the new one in place found right size screw from my tool box, tightened it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CHARLOTTESVLE, VA
- Parts Used:
- 5230W1A011B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replacing top vent filter
Followed owners manual instructions to the letter: removed two top screws, opened the unit door so I could slide out the old filter. We don’t cook much at all in the unit, mostly just heating coffee and reheating leftovers. BUT! The top grill was pretty greasy and needed hot soapy water to clean, including in the depths of the top area. The whole process, especially the company website for part ID and purchase, was slick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from PINELAND, SC
- Parts Used:
- 3B73362F
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door switch malfunction
Take cover off microwave. Check door switches to determine which one was faulty.Remove and replace faulty switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dick from SANDY, UT
- Parts Used:
- 6600W1K001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave fan would come on when door open. Timer and unit would not switch on.
I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.
https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PURCELLVILLE, VA
- Parts Used:
- 4370W1A006B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The new part was too thick for the worn out plastic ring which is obsolete.
Needed to raise the part to match the ring. I used peanut butter to hold plastic shim while replacing to hold it in place. Built in Oct. 2009.
Was this instruction helpful to you?
Thank you for voting!