MV1648AD (CWHELGA) LG Microwave - Instructions

Used fingers to pull damaged cover away from microwave interior body. Used fingers to snap replacement cover into open slots.

Cover snap right into special slots.

Originally called it "grease filter" until I found very small print "air filter" on damaged original. Part #PS3527528

Slipped into place with ease -- right bottom of microwave

Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.

Wanted to see the instructions before I install it.

Pop old one out and replaced it with new one.

Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.

Removed one panel and screws from broken door. Attached new handle and replaced panel by snapping in place...Very easy to instll..

Received my replacement Tray,Glass in only 2 days. Opened it and placed it in the Microwave. Yep, it was that easy!

removed screws from bottom of microwave... lowered bottom plate.. unplugged motor and replaced with new motor/AC synchronous. Reinstalled bottom plate......... DONE!!

I removed the old door and installed the new door

Problem was a faulty door latch switch. I easily accessed the switch by removing the control panel, total of 4 screws. After that, just disconnected the three switch door latch assembly and connected the new one. Took about half an hour and was very easy. Unit works perfectly now.

1. Removed unit from the cabinet. (2 screws). 2. Remove the outer microwave metal shell. (10 screws). 3. Locate and remove part. (3 screws). 4. Install new part and replace all screws. 5. Install unit back into cabinet. So easy. I will share this site with all of my friends.

Ordered the switches from Partselect, arrive in two days. Had trouble removing the plastic connectors from the old switch terminals, one of the plastic protectors broke, but was able to reuse it. It took a little figuring out how to remove the existing switches. Must push in a tab and rotate the switch on a little pin, then remove. Must be careful not to break the plastic tabs holding the switches in place. Replaced all (3) switches at the same time. All in all it was pretty easy.

First, I checked YouTube to see if there was a video showing how to do the repair ... It's as easy as unplugging the power cord, removing 6-8 screws on the bottom panel, unplugging the wire harness from the AC synchronous motor, removing two screws hold the motor in place, putting the new motor in place with the two screws, connect the two wires to the brass tabs, replacing the bottom panel, reconnecting the power - and you're done. Easy!

remove the screws from the bottom, leave tthe light wires attached. There are two screws holding the motor on, disconnect and mark the old unit where the yellow wire goes. Mount motor with two screws and connect wires. Turn on Miicrowave for 10 sec, to be sure all is correct. Attacch bottom cover and reattach power cord. Before doing anything make sure power cord is disconnected and reattached when sealed.