80419 LG Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brent from Bend, OR
- Parts Used:
- 5304440323
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle
Removed the retaining clip that keeps the door on, took the door off. Removed the plastic rim that is clipped into place. Removed old screws holding on handle and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Punta Gorda, FL
- Parts Used:
- 5304440323
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle was broken R&R required.
Open the door and start at the outside perrimeter of the plastic moulding by inserting the putty knife and gently prying up.I started at the 2 latches that secure the door when it closes.Work your way around to the top and bottom. I was able to leave the portion of the plastic moulding by the door hinges still intact while removing the screws for the handle and replacing with the new one.After handle is on gently snap moulding back in place.Remember start at the inside of the door in the small opening at the outter edge of the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tony from kewanna, IN
- Parts Used:
- 5230W1A012E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed grease filters for a used over range microwave
ordered on the part select web site, came quickly, order was correct
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Hephzibah, GA
- Parts Used:
- 5304440323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken micorwave handle
It was really simple. I used the putty knife the seperate the plastic trim, paying particular to start near the latches as someone else posted. Once the trim was pulled back Wow the screws were right there. I unscrewed the broken handle and attached the new handle. It was really easy and my wife thinks I'm amazing thanks for the help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from OZARK, MO
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
One of the switches in a component that door activates when shut.
I replaced the whole component with all three switches in it even though only one switch was bad . Taking out one switch out of the holder unit would probably have damaged the unit that was holding the switches. Easy install and it works great again .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from DETROIT LAKES, MN
- Parts Used:
- 1B71961H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke the round glass tray
new glass tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VIRGINIA BCH, VA
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
would not start.
diagnosed defective 'door-shut switch' in the switch holder assembly. rather than replace switch, replaced entire locker holder assembly which made for a very simple and easy repair...not to mention very inexpensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Shreveport, LA
- Parts Used:
- 5304440323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Door Handle was broken
Removed the inside door cover by taking a putty knife and inserting it by the door levers all around the door while pulling forward to seperate the cover so the screws that held the handle on could be reached. However, the part did not fit and had to be returned. Replaced cover by pinching it back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garth from Albuquerque, NM
- Parts Used:
- 5304440323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the handle broke in half
With the amount of force needed to open the microwave door I can see this repair repeated. Some of the handle was still attached to the door so I could open it easy enough. there is a flamge covering the scerws to remove the handle. using a small flat blade screw driver aids in the removal of the flange to expose the screws. the square flange surrounds the entire frame of the door.remove the screws located in the recessed edge along the outside edge of the door.do this by viewing the location of the peices still attached to the door. after removing the screws and broken parts of the old handle,place the new handle in the cutouts where the handle is located,replace the screw,this may take some force since the handle is new. reposition the flange to the framevia the snaps along the edges and becareful not to force it because damage to the snaps are possible.thats it,two minute repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Caledonia, MI
- Parts Used:
- 5304440323
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic door handle broke at upper screw
Used putty knife to unsnap tabs to separate inner trim on top, bottom and handle sides (left the hinge side attached), removed upper and lower screws, replaced handle, reinserted screws (tight fit, big fingers, several dropped screws, one under the stove = 15+ minutes), re-snapped trim
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from BRONX, NY
- Parts Used:
- 5889W2A012F, 1B71961H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass was cracked and the turntable burned
Just removed and replaced by putting the new turntable and glass in, 1, 2, 3; that's it. I'm so thankful for this site because I would have had to buy a whole new microwave. Thanks a million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Philadelphia, PA
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave not heating, everything else works
Not knowing which of the switches to replace I ordered all three in the assembly. Replacing the full assembly was easy, first unplug the microwave. Then remove the top cover to access the screws that hold the control panel in place and let the control panel hang. There are two screws that hold the assembly in place - remove those. I used needle nose pliers to pull the wires off of the switches and immediately put the wires on to the new assembly so there was no confusion on what wire went where. Place the assembly back in position, replace the two screws to hold it in, put control panel in place and secure screws. Replace top cover and plug in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Wantagh, NY
- Parts Used:
- 5304440323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke
Separated the two elements on the front door. Then inserted the new handle and reconnected the front door. It was an easy installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SEVERN, MD
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
food does not get hot, carousel did not turn, all other indicators worked
Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from SELLERSBURG, IN
- Parts Used:
- 5304440323
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke on the unit. Nothing but two screws showing
Open the microwave door.
On the interior of the door, there is a plastic molding around the locks and most outer part of the door. Pop that with a flathead screwdriver or butter knife. You’ll immediately see two screw heads. Screw counterclockwise to release the fragments of the old handle. DO NOT THROW THOSE SCREWS AWAY. Reattach new handle using the same screws. Pop the piece of plastic molding back in and you’re done.
On the interior of the door, there is a plastic molding around the locks and most outer part of the door. Pop that with a flathead screwdriver or butter knife. You’ll immediately see two screw heads. Screw counterclockwise to release the fragments of the old handle. DO NOT THROW THOSE SCREWS AWAY. Reattach new handle using the same screws. Pop the piece of plastic molding back in and you’re done.
Was this instruction helpful to you?
Thank you for voting!