KCMS1555RWH0 KitchenAid Microwave - Instructions

Followed the instructions that others with a similar problem had written about. Their experience was very helpful. My experience with Part Select was the best! Part recived in less than 24 hours. Happy household, wife thinks I'm worth keeping!

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

Removed the four face plate screws and set it aside. Then I removed the three screws holding the base plate to the wall mounting. Removed the wall plug and lifted the microwave out. I then removed all the screws holding the cover on the microwave and pulled the case to the rear This left the door latch accessible. Since the old latch had broken and fallen off, I just had to figure how the new one was to be installed This was very simple to figure out and it took me about five seconds to put the new one in.. Be careful when installing because all the parts are plastic and susceptible to breakage. I then reinstalled the microwave cover and after plugging it in ,pushed it into the wall cavity and put all the screws in to hold the oven in place. I next installed the face plate and every thing was in working order, A very simple project.

Replaced the diode (aka wire-vltge) in the HV circuit after removing cabinet cover using both the secure torx screw drvr & phillips head screw drvr. The hardest part of the job was finding the secure torx nut drvr tool on the internet & purchasing same.

The tip on the end of the latch broke off, so I had to carefully pry it back in without breaking the new piece. Took a few tries, but got it.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

My wife was pushing a few buttons with her knuckle (hands were full)and the microwave just turned off. Just like we had blown a breaker. First I unpluged it. Then I removed the phillips screws of the front panel, and found and removed the ceramic fuse. 3 days later I received the new fuse in the mail, and put it in. I plugged the microwave back in and it works great.

I had purchased the wrong replacement tray from Amazon and could not find the right one on their website. Yours was exactly what I needed.

very easy just put the tray on the turntable. excellent delivery service arrived sooner then expected.

1. Remove the trim frame off of the front of the cabinet (4 Phillips screws). At this point, take glass plate and turntable frame out of unit. 2. Slightly lift the unit off the cabinet frame (which is attached to the cabinet) so the feet on the microwave allow the unit to clear the frame and then remove microwave from the cabinet. 3. Once slightly removed from the cabinet, unplug the unit before completely removing it from cabinet. 4. Take 2 Phillips screws out of the side panels. 5. Take about 6-7 T20 Star Pin screws out of the back of the panel. (This may require you to purchase this special tip if you don't have it in your toolbox). 6. Slide the microwave cabinet toward the rear of the unit (the front portion clips into the frame ... don't try prying it off because you'll damage the unit). 7. Completely remove the microwave cabinet housing. 8. Be careful not to damage or catch any internal wiring inside the unit while the cover is off. 9. Turn unit on it's back and remove 4-5 Phillips screws holding the bottom cover in place. Remove bottom cover. 10. Now notice that the turntable motor is completely exposed. 11. Remove the wiring harness from the motor (notice which connection clip has the black wire). 12. Remove the one Phillips screw holding the motor to the frame. 13. Clean around the area in case food spills may have gotten into the area. 14. Insert new motor, put Phillips screw back in and attach power connection. 15. From this point on, just reverse steps to re-assemble microwave and put back in cabinet. 16. Test new turntable motor. 17. Enjoy the smile from your wife because she can now use the microwave!

Took off the outside metal cover determined what the problem was immediately saw the broken latch ordered the new one received in 2 days snapped it into place the door opened then replaced the outside metal cover good as new.

removed microwave cover screws, unplugged motor, screwed on new one

This plastic door latch bracket controls the door opening. Ours broke after 7 years of use. Probably just the plastic fracturing after years of use. Hardest part is finding the special driver to unscrew the housing around the microwave so that you can get to the control panel. Ask for something that looks like an allen wrench with a hole in the middle. I took a picture of the screw in the microwave and brought it to a big box store and asked for the correct driver. I have a feeling that a "real" hardware store (like Ace or TrueValue) may have been able to just direct me to the correct screw driver but I'm cheap so I though a big box store would be less expensive for a tool that I may never use again. Once you get the correct screw driver, opening the microwave is pretty easy. MAKE SURE THE MICROWAVE IS UNPLUGGED BEFORE YOU GO ANY FURTHER. There are a number of these "special" screws (4 to 6) and some regular screws to remove. Once you pull the housing off the microwave look at the release latch inside (behind the release press plate). You should be able to jiggle it out especially since it is probably broken on one side. Be sure to find and remove all the broken pieces. Mine had just the main latch and a small piece that broke off. Pull it out and you are ready to put the new one in. It is a little difficult putting the new latch bracket in. Try inserting one side into the holder hole and very gently pressing the other side in. Be patient; with a little pressure it will snap in. Then you simply put the housing back on, put the screws in and every thing should work. $20 bucks for the part and a half hour of work (after you find that special screw driver) is much better than buying a new microwave. Good luck!

Had to remove 3 screws that held the case in place,it removed easily. The control panel that the door latch was locked into required removing two screws and then lifting up slightly while pulling forward. This allowed enough room to put the new door latch bracket into place. Then re-assemble in reverse order. Total time about 30 minutes.

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced