YKHMS1850SW0 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lois P from Morris, IL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke rotating plate, it fell off counter after being washed
Opened door and put new plate in.
Placed order on Thursday evening and received Sat Am
Placed order on Thursday evening and received Sat Am
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monty from Mansfield, TX
- Parts Used:
- W10642989
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace turntable motor
removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grace from WOODSTOCK, GA
- Parts Used:
- W10250593
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced vent grill.
Took this great-grandmother of 7 less than 3 minutes. Only needed a Phillips screwdriver. Easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George S from LEWES, DE
- Parts Used:
- W10250593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper trim piece fell off
1. Remove two screws
2. Install new part
3. Replace two screws
2. Install new part
3. Replace two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from AUBURN, AL
- Parts Used:
- W10250593
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Brittle, plastic mounts broke,Vent fell when cleaning
Removed remaining plastic around 2 screws. I recommend a Magnetic Phillips Screwdriver, screw holes are a little Offset, and mount screws are small. I used Needle Nose Pliers to hold screw, to get it started. Really simple install.
Was this instruction helpful to you?
Thank you for voting!
light that illuminates the range would not work.
replaced the socket per recommendations on this web site. this did not correct the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael J from LORAIN, OH
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb which lit the surface of the range.
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from ORANGE, CA
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from brockton, MA
- Parts Used:
- W10709921
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I noticed that the hood lights were out.
I took off the glass panel underneath the microwave and replaced the 2 bulbs in less than 3 minutes by myself with only a phillips head screwdriver. I was very pleased with the service I received and more pleased with myself that I did not have to call in a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mouang from Sacramento, CA
- Parts Used:
- 4393799
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Glass tray shattered
Ordered the glass tray and installed it. Received the orderin about two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Smithtown, NY
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
machine was dead.
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Cherry Valley, MA
- Parts Used:
- W10250593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic bracket that holds screw was broken
The repair was simple, just unscrew two screws and put the new one on. Took less than five minutes. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from Charleston, SC
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
"Lost" microwave tray
Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Henderson, NV
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cooking tray chipped
replaced with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Pompano Beach, FL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken
put the turntable in and had a Rum and Coke to celebrate. Your service was GREATTTTTT...
Was this instruction helpful to you?
Thank you for voting!