YKHMS2040BS0 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace glass tray and charcoal filter
Replaced broken glass tray. Used two screwdriver to remove top front panel to replace charcoal filter. Microwave parts diagram with descriptions and part numbers made the project very simple. Price of parts was substantially less than manufacturers price schedule. A very satisfied customer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from MAYS LANDING, NJ
- Parts Used:
- W11025649
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
needed microwave mounting bracket
mounted bracket, case closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kat from Hudson, NC
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights bulbs burned out
Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from MIDDLEFIELD, CT
- Parts Used:
- W10727360
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Failing Door Switch. Preventing unit from operating.
Removal of Phillip Head screws from Top vent and Control panel. Removed Torx head screw to remove entire switch assembly. Removed three wires to switch leads. Unclipped old switch. Replaced wires and inserted New switch in to clips. Attached assembly with Torx screw. Set Control panel back into place and screwed in top screw. Replaced upper vent with 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from MOUNT ULLA, NC
- Parts Used:
- W10269458
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The close door warning kept coming on and the microwave would not run
Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from LATHROP, CA
- Parts Used:
- W10709921
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out lamp
This should be a 1 minute repair. However, there are a few issues. First, make sure you order the correct bulb. Mine is a halogen push in bulb, but the parts list showed a screw in bulb.
Remove power from the unit OR be sure that the light is turned off with the push switch.. The display will show the status as you rotate through the dim levels.
There is a single Phillips head screw holding the cover on the underside of the over stove microwave. carefully remove it. When loose the panel will drop down and you will find the old bulb in the center of the front of the opening. Remove the bulb. Now the important part. Carefully unpack the new bulb being careful to not touch the glass with your bare hands or fingers. Then insert the bulb into the socket.
If you unplugged the unit then plug it back in and push the switch to check that the new bulb works and is in the socket, then turn it back off.
Carefully lift the cover back into position and replace the screw. This is the hard part as you are working upside down and can't really see when it is lined up properly. When you have the screw back in and tight you are done. Press the light switch to enjoy your lit up stove again and put your tools away.
If you get your fingers on the glass bulb then clean it off with some rubbing alcohol and a paper towel to remove any finger oils before you put the cover back in place. Finger oils can boil with the heat of the lit bulb and cause the glass to explode. This holds true for any halogen bulb.
Remove power from the unit OR be sure that the light is turned off with the push switch.. The display will show the status as you rotate through the dim levels.
There is a single Phillips head screw holding the cover on the underside of the over stove microwave. carefully remove it. When loose the panel will drop down and you will find the old bulb in the center of the front of the opening. Remove the bulb. Now the important part. Carefully unpack the new bulb being careful to not touch the glass with your bare hands or fingers. Then insert the bulb into the socket.
If you unplugged the unit then plug it back in and push the switch to check that the new bulb works and is in the socket, then turn it back off.
Carefully lift the cover back into position and replace the screw. This is the hard part as you are working upside down and can't really see when it is lined up properly. When you have the screw back in and tight you are done. Press the light switch to enjoy your lit up stove again and put your tools away.
If you get your fingers on the glass bulb then clean it off with some rubbing alcohol and a paper towel to remove any finger oils before you put the cover back in place. Finger oils can boil with the heat of the lit bulb and cause the glass to explode. This holds true for any halogen bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAN from CARPENTERSVLE, IL
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
light bulb burnt out .
Turn off power supply at breaker . Replace old bulb with new bulb .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hudson, MI
- Parts Used:
- WPW10156813, WP8206419
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Top support for door switch broke.
Part of the support was missing. I had to remove the two switches and put them in the new bracket
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MERIDIAN, ID
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Range light bulbs were burned out
We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Cincinnati, OH
- Parts Used:
- W11252182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turntable broke in half, ring turn needed replaced
I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next
Service was fantastic, parts were ordered one day and received the next
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pablo from Burlingame, CA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb burned-out
screwed in new bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Ocala, FL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass tray
Washed the glass tray and put in the microwave oven. Easy..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Port St Lucie, FL
- Parts Used:
- W10435116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable coupling
Rep knew exactly what I needed when I described where the part should go on my microwave - price great - shipping great - installed in seconds. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles R from Libertyville, IL
- Parts Used:
- W10245183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Loud buzzing noise and no heat.
PartSelect website indicated replacing the high voltage power supply diode is the solution for "no heat" 99% of the time, but the diode was OK. There is more info at the website concerning the case of "loud buzzing and no heat" indicating the magnetron needs to be replaced. As an electrical engineer with knowledge of microwave components, this was also my best guess. However, getting to the magnetron is not the easiest job, but it's not impossible. You also have to be careful to bleed off any charge stored on the high voltage power supply capacitor. Luckily, I found my KitchenAid service manual tucked away inside the unit since I couldn't find it online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from OVERLAND PARK, KS
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out bulb
Husband replaced the bulb
Was this instruction helpful to you?
Thank you for voting!