KHMS1850SWH1 KitchenAid Microwave - Instructions

This should be a 1 minute repair. However, there are a few issues. First, make sure you order the correct bulb. Mine is a halogen push in bulb, but the parts list showed a screw in bulb.
Remove power from the unit OR be sure that the light is turned off with the push switch.. The display will show the status as you rotate through the dim levels.
There is a single Phillips head screw holding the cover on the underside of the over stove microwave. carefully remove it. When loose the panel will drop down and you will find the old bulb in the center of the front of the opening. Remove the bulb. Now the important part. Carefully unpack the new bulb being careful to not touch the glass with your bare hands or fingers. Then insert the bulb into the socket.
If you unplugged the unit then plug it back in and push the switch to check that the new bulb works and is in the socket, then turn it back off.
Carefully lift the cover back into position and replace the screw. This is the hard part as you are working upside down and can't really see when it is lined up properly. When you have the screw back in and tight you are done. Press the light switch to enjoy your lit up stove again and put your tools away.
If you get your fingers on the glass bulb then clean it off with some rubbing alcohol and a paper towel to remove any finger oils before you put the cover back in place. Finger oils can boil with the heat of the lit bulb and cause the glass to explode. This holds true for any halogen bulb.

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Put s pot under were you take the screw out.If you drop it you can get it easy

Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.

I just had to remove the screws, and the broken parts of the old grill vent (plastic part that sheared off) and put the new grill vent in place and use the existing screws to attach and that was it!

Super easy.

Remove the two screws to the plastic vent strip at the top of the unit. That exposes a metal cover (upper right) held in place by two more screws. (Found that removing the screw holding the key panel in place and moving that out of the way made for more work room) Remove the metal cover. The HV diode (visible) on one end is secured to the chassis by a screw. The other end is fitted to the HV capacitor. So unscrew one end and pull the HV diode off the capacitor. The replacement fits on like the old one came off. Very simple repair. But it would be safe to short the capacitor terminals to the chassis first. Noticed that it appeared the sparking was caused by the HV diode's outer casing being worn by the asbestos covered wire next to it and laying against it. I made sure the two were not touching, before putting the covers back on. Also, the problem started with an occasional spark when the MW started. It quickly deteriorated to a full, non-stop electrical sparking. You can hear it, smell it, and see it through the top vent. You don't need to remove unit to work on it.

Take off top facing over microwave using screwdriver also protection plate for diode and capaitor. Disconnect diode from frame, bracket to capacitor then remove, disconnect wires leaving diode on capacitor for right connection, replace, rewire done.

One Phillip's screw to remove glass on bottom of unit. Pull old bulb out & insert new bulb. Replace glass & screw.

Unplug the microwave. Removed the glass tray, the roller ring, and plastic piece that sits on the motor shaft from the inside of the microwave. Remove the 12 Phillips head screws from the bottom of microwave, let the bottom hang down on the mounting hooks at the rear of the microwave. Remove the 2 torx screws from the mounting bracket under the microwave lower the turntable motor remove the two leads. Transfer the rubber washer from the old motor to the new and reassemble and test. It took longer to write these instructions than it did to do the job.

Hint: if the microwave is over a stove lay a towel across the stove to catch any screws that may fall.

Good luck and enjoy your fully functional microwave!

Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.

The replacement part was identical to that of the original microwave and arrived in perfect condition.

The repair was extremely simple - too screws and a "snap" and it was done.

Couldn't be happier with the results. Thanks, Part Select!

Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.

Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.

Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.

Replaced bulbs easily.