KHMS147KSS1 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Lithia, FL
- Parts Used:
- 8205008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace vent grill
Installation was very easy and only took about two minutes. I am extremely pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Statham, GA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement
Easy, perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Excelsior, MN
- Parts Used:
- W10435116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotating glass dish assembly making stange noise
The lady in the Nova Scotia call center should get all the credit for being able to identify the part I needed from only the very limited information I was able to give her. Employee of the month for her. She also had such a great can do attitude. Lawence Baier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from La Jolla, CA
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke a 15 year old glass cooking tray
Ordered the item on a Monday at 12pm and it arrived the next day. Amazing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janice from dunn, NC
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass cooking tray droped and broken
just replace need cooking tray
Was this instruction helpful to you?
Thank you for voting!
Broken turntable support ring and missing support
Watched video which reminded me to order support for the turntable support ring and did exactly what the person in the video did. Excellent and prompt service and all parts fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CJ from Bullard, TX
- Parts Used:
- W10435116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turn table would not turn
After researching online, I found that I needed the turntable drive coupling, part#PS993087. when I went to your site it showed the same part but the part number had changed but said it would fit my microwave. Well, I was really surprised and happy when the part I received 3 days after I placed the order, with normal shipping,fit perfectly and now my turn table in my microwave works. I have marked this site a a favorite and will use it I'm sure soon. Being a single women and having to figure out how to fix the things on a small buget, I'm learning a lot and have a lot of respect for men that know how to do all the repair stuff. Thanks so much, I have been able to mark this off my list of things to fix. Have a nice day. Cj- age, 58
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Winter Park, FL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken cooking tray. Food not heating evenly.
Simply placed new dish on the rotating hub.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Washington, IL
- Parts Used:
- 6800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Replace charcoal filters in microwave - vents inside.
Remove the screws holding the bottom vent plate to the upper unit, using a Phillips head screwdriver. Loosen a front screw last, but don't remove it. While supporting the plate in one hand, unscrew the final screw with the other. Lower the front of the bottom plate - tabs in the rear will prevent the plate from falling out. Bend the outer tabs holding the old filters in place, to allow them to be slid out. Insert the new filters & bend the tabs back into locking position. Raise the bottom plate and finger tighten a front screw. Replace and tighten all screws. This is also a simple way to remove/clean/replace the mesh filters. I've pulled the D-rings off trying to slide them out from below.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Ft Lauderdale, FL
- Parts Used:
- 8205008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken vent grill for Kitchenaid microwave oven
I just looked at the broken one to see where it broke and looked at the microwave. I realized that there were two screws that were supposed to hold the vent grill along with 3 slots on the bottom. I inserted the slots on the bottom into the preset spaces for them, lined up the top with the two screws and screwed them into place. Checked to make sure the screws were not too tight and that was it. New vent grill in place and ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Phoenix, AZ
- Parts Used:
- 6802A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave Vent Hood Filters
Not so sure this would qualify as "instructions", but I only needed a screwdriver because the "D" rings of the old vent filters broke off and I had to pry to old ones out. Keep in mind, I am mechanically disadvantaged and can barely change an A/C filter ... that being said, all I did for this order was input my Model number and PartSelect found the correct replacement part. I receive the parts super quick (faster than the other 2 purchases I did that day). The only bummer was the packaging ... super huge box for small tiny parts. Otherwise, I now know where to go for replacement parts. This project should be a "no-brainer" for most DYI's, so getting the right parts with just a model number was lifesaving for me :0)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larrt from Minooka, IL
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Huntington Beach, CA
- Parts Used:
- 8184581
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Microwave was making a grinding sound
Problem was easily diagnosed using the internet as a resource, problem was a bad stirrer motor. Hardest part of the repair was the removal of the microwave. Once off the wall, you remove the outer cover and a molded plastic casing directly underneath the outer cover at the top of hte microwave to expose the stirrer motor. Removed two screws and two wires and the old motor is out. Did exactly the opposite to install the new motor. The kit I recvd included among other things the motor, a new inside cover, plastic rivets and even silicone to seal the inside cover. I am sure I saved a couple hundred dollars by doing myself.
Was this instruction helpful to you?
Thank you for voting!