KHMS147HSS0 KitchenAid Microwave - Instructions

I ordered another one and placed it inside the microwave. It works and fits perfectly. I received the order exactly as scheduled.

Snapped and screwed new part in minutes

Unscrewed three screws and used putty knife to pry door cover off unscrew door handle put on new face plate and redo the three screws and clip back on oh you have to unclip the glass part and put on to the new face plate before putting on new door front to microwave

Replaced the supports and rack.

PartSelect website indicated replacing the high voltage power supply diode is the solution for "no heat" 99% of the time, but the diode was OK. There is more info at the website concerning the case of "loud buzzing and no heat" indicating the magnetron needs to be replaced. As an electrical engineer with knowledge of microwave components, this was also my best guess. However, getting to the magnetron is not the easiest job, but it's not impossible. You also have to be careful to bleed off any charge stored on the high voltage power supply capacitor. Luckily, I found my KitchenAid service manual tucked away inside the unit since I couldn't find it online.

I loosened the 2 screws at the top, removed the broken-off pieces of the old part, then easily placed the new part and tightened the screws.

The whole process was so easy! It was easy to order the part. It came directly to the house in just a few days.

Thanks.

Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!

E. Robinson

I removed the two screws on the side. Took a putty knife and gently pryed it away from the rest of the door. I took the handle off the old door and put it on the new door. I took the glass and the plastic frame that holds it on off the old door and put it in the new door, I snapped the new door back on and relaced the screws.

Thank you. The part was easy to find on your web site. The order came within 3 working days and the part replaced

both of the pieces have a tab that help remove the pieces. They slip right out and new ones are putin place.

Opened door and put new plate in.

Placed order on Thursday evening and received Sat Am

It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!

Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.

I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock

First I removed the 2 screws holding the panel on. I then removed the cracked panel. It was held in place by small "catches" built on to thew door. Replacing the new panel was easy, except, I forgot to attach the old handle. I was afraid I would break the new door but it came off with some prying. After replacing the handle, the door went on easily.

It's a simple repair but costly. Just open the door remove the three screws on the side of door. Now use a small screw driver or metal putty knife to remove the chooker collar around the door " be careful this can easly be broken". Okay now the metal inner door is easier to remove if you slightly bend the tabs up around the door. Look carefully you should be able to see where they catch. Once you do that carefully seperate the outter door cover. Careful sometimes it will pop right out and fall. Please no more further repairs needed. Just screw in the new handle push tabs back out on the metal inner door then snap everything back together and reinstall the three screws.