KCMS1555RBL0 KitchenAid Microwave - Instructions

Took microwave out of builtin cabinet with 4 screws.
Put microwave on center island and removed cover.
Tested interlock switch with volt meter and it appeared ok so I put my kit back in box and sent back.
Took out magnetron unit and replace with new part.
Put cover back on and test.
All is working and installed back in cabinet. Two weeks later all still working great.

Unplug microwave. Remove the cover(mine had six screws- including 4 special screws I was able to remove the special screws with pliers. Remove the broken latch. Then you must take out the two screws which hold plastic plate that has a bunch of wires connected to it. Otherwise you can’t install the new latch without breaking the side “axle” of the latch. Once you remove the plastic plate the new latch will snap right into place. Reinstall the plastic plate w the screws and you are good to go. Note of caution. The micro cover edges are as sharp as a knife. Use gloves!

Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos

Removed M/W oven case/cover. Identified part needed. Found part online with in 2 minutes, ordered new door latch actuator, installed with part arrived within two minutes, reattached case/cover, reinstalled M/W.

Replaced Door latch Bracket.
Filed a bit off the bracket connection fingers so to fit into the slot.

Remove outside cover of microwave.Note that there are 3 unique security screws that you will need a special screwdriver to remove. There is a YouTube video that shows how to install new part. Although this was a lot cheaper than buying a new microwave the cost of $57.00 plus shipping for this 3 inch plastic part was ridiculously expensive.

Remove from cabinetry, take cover off and had a very difficult time removing the plastic form that has the switched in. Replace the lowest of all the switches, and then again very difficult time getting the plastic form back in. Some of the plastic even broke during the process but not any that could prevent it from working as it did before. I had ordered a fuse, 2 packs of 2 switches as there are 3 switches but only had to use 1 to get it working again. Tested after switch install, put the cover back on and reinstalled in the cabinet.

I'm so glad that the site was available on the internet!
I simply threw away the broken turntable and inserted the new.
I did not have to wait for a repair person!
Great! Thank you.

I called to make sure I was replacing the correct part. I paid over the phone and it came the next day. Very very easy process.

The tip on the end of the latch broke off, so I had to carefully pry it back in without breaking the new piece. Took a few tries, but got it.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

1.ordered the part 2.during wait time for part,i epoxied the broken ear of the door latch bracket back on to the broken part.3.waited 24 hours for epoxy to set,4.installed the repaired part.5.reassembled the microwave and reinstalled in the wall unit.6.days passed and the ordered door latch bracket finally arrived.7.we are using the microwave daily with the repaired door latch bracket,but we will keep the new part in reserve,just in case!JUST CAN NOT DO WITHOUT OUR MICROWAVE!

My wife was pushing a few buttons with her knuckle (hands were full)and the microwave just turned off. Just like we had blown a breaker. First I unpluged it. Then I removed the phillips screws of the front panel, and found and removed the ceramic fuse. 3 days later I received the new fuse in the mail, and put it in. I plugged the microwave back in and it works great.

Took off the outside metal cover determined what the problem was immediately saw the broken latch ordered the new one received in 2 days snapped it into place the door opened then replaced the outside metal cover good as new.

Replaced the diode (aka wire-vltge) in the HV circuit after removing cabinet cover using both the secure torx screw drvr & phillips head screw drvr. The hardest part of the job was finding the secure torx nut drvr tool on the internet & purchasing same.