KHMS1850SBL0 KitchenAid Microwave - Instructions

submitted manufacturer info to website and voila! a new glass turntable arrived in 2 days. I don't do well with computers, my 23 yr. old daughter was impressed......couldn't be easier! thanx! will definitely revisit your site

All I had to do was open the microwave door and place the turntable on the designated grooves, wha lah it fit. I am now back in business. Thanks to partselect, I found my replacement, ordered and it was shipped in no time.

put the turntable in and had a Rum and Coke to celebrate. Your service was GREATTTTTT...

I followed the manufacturer's installation instructions. Everything worked perfectly.

Removed one screw lowered glass cover removed burned out bulb replaced with new one put glass back reinstalled screw. Dune 5 minutes back in business

Oprnef the door frame and took off old handle

Having the correct model number helps:
Just place the parts in the microwave and it worked.

I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.

Open compartment, installed bulb, closed compartment

took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse

I purchased the door handle to model KHMS1850SWH0 for around $50; the model I have,KHMS1850SWH1, only offers the entire door as a replacement for over $200. The earlier model door handle fit great with no problems.

The repair was easy, I just took off a few screws and found the broken latch spring. The real story is how easy it was to find the replacement spring from Partselect! I couldn't believe they had it, and even better yet, I ordered it one afternoon, and it came the next day with normal shipping! Unbelievable! Then I just popped it in and replaced the covers I had removed and it was working again!

Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!

This is an over stove top mounted oven. Remove oven from mount and place on a work surface with padding to support the lamps and vent holes. Strip the case off and locate the noted other "most likely" parts. Watch out for the Capasitor. Read the test note available for each part; Diode, Thermister Fix, Capasitor and Magnitron. Do the test checks. My issue wasn't obvious because I think the Capasitor was discharged and needed to be hot to check the Magnitron. (I'm not an electrical engineer so...) At this point I did the foolish thing...I plugged the unit in and ran it. Watching from a distance I saw sparks fly from the top side of the Magnitron with the same result from my cup of water (cold-no sprks here.) I replaced the diode and tried again, same result. I ordered the Mag and the Thrmst-Fix. Thrmst-Fix was on BO when the Mag got here so I installed the part. Had to remove several pieces to afford room to work and still had to stretch and pry to get the old out and new in. Mag is held in place with Torx screws so check that before you start. No other tool works. Mag was the problem for this unit. Some problems encountered: Parts and pieces were quick in arriving as long as they were not Back Ordered. Be careful to follow a thread for your product to order parts. These review/instructions are mixed for simular appliances and sometimes lead off to other part lists and numbers. Prices differ from model to model, list to list and the part numbers change. Go back to your product and then trace for the correct parts. I noted a $40 price dif.between Magnitrons from simular part lists. When you receive the part check to match the part numbers, Manuf. no. are different from the Part Select No. but can be crossed. Otherwise using this site's instructions, checks, insulated tools, big rubber gloves and a face shield I managed to save a $600 machine from the junk pile. Parts as ordered were recieved and return of un-touched parts were accepted by Parts Select without unexpected hassle. Thanks for a positive experience.

Problem was easily diagnosed using the internet as a resource, problem was a bad stirrer motor. Hardest part of the repair was the removal of the microwave. Once off the wall, you remove the outer cover and a molded plastic casing directly underneath the outer cover at the top of hte microwave to expose the stirrer motor. Removed two screws and two wires and the old motor is out. Did exactly the opposite to install the new motor. The kit I recvd included among other things the motor, a new inside cover, plastic rivets and even silicone to seal the inside cover. I am sure I saved a couple hundred dollars by doing myself.