KHMS1850SBL0 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from MERIDIAN, ID
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Range light bulbs were burned out
We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from Vancouver, WA
- Parts Used:
- 8169539
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hood light wont work
Turned power off. Removed all the screws from bottom removed socket and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pablo from Burlingame, CA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb burned-out
screwed in new bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Vero Beach, FL
- Parts Used:
- W10250593
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The vent bracket broke, that in which in the entire vent needed to be replaced.
Removed the three screws and replaced the with the new vent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Cincinnati, OH
- Parts Used:
- W11252182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turntable broke in half, ring turn needed replaced
I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next
Service was fantastic, parts were ordered one day and received the next
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Ocala, FL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass tray
Washed the glass tray and put in the microwave oven. Easy..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Charleston, SC
- Parts Used:
- W11256462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
visible sparking inside top of MW unit
Remove the two screws to the plastic vent strip at the top of the unit. That exposes a metal cover (upper right) held in place by two more screws. (Found that removing the screw holding the key panel in place and moving that out of the way made for more work room) Remove the metal cover. The HV diode (visible) on one end is secured to the chassis by a screw. The other end is fitted to the HV capacitor. So unscrew one end and pull the HV diode off the capacitor. The replacement fits on like the old one came off. Very simple repair. But it would be safe to short the capacitor terminals to the chassis first. Noticed that it appeared the sparking was caused by the HV diode's outer casing being worn by the asbestos covered wire next to it and laying against it. I made sure the two were not touching, before putting the covers back on. Also, the problem started with an occasional spark when the MW started. It quickly deteriorated to a full, non-stop electrical sparking. You can hear it, smell it, and see it through the top vent. You don't need to remove unit to work on it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from OVERLAND PARK, KS
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out bulb
Husband replaced the bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from PALMYRA, VA
- Parts Used:
- W10315274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Supports were bad
Replaced the supports and rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon C from MEDFORD, OR
- Parts Used:
- W11252182
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Microwave didn't have support ring when house was purchased.
Removed turntable
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CARMELO from LOVETTSVILLE, VA
- Parts Used:
- W10709921
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both lights failed. Replaced with new bulbs.
Unscrew lens and direct access to surface light cavity. Removed old light bulbs and replaced with new bulbs. Reassembled lens cover and turned lights on successfully. Took less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from SUFFERN, NY
- Parts Used:
- W10709921
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb under the microwave burned out
Used a philips head screwdriver to remove one screw holding the light cover. Pulled out the old bulb and inserted the new one. Replaced the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANNY from SAINT JOHNS, FL
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light in microwave
Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hild, from STRONGSVILLE, OH
- Parts Used:
- W10250593
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Easy fix
The part is held in place with two screws. A poor design for sure. The replacement part is a direct fit once the two screws are removed. Reuse the same screws, don't order new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vince from LAHASKA, PA
- Parts Used:
- W10250593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plastic holders cracked causing the Vent Grill to completely separate from th Microwave.
Repair took kess than 5 munutes.. Align plastic guides for the Screws and using a Philips screwdriver commence to tightening same .
Was this instruction helpful to you?
Thank you for voting!