KHMS155LBT0 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ken from DALLAS, TX
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic on original grill clips broke.
Took out 2 phillips screws on top, pulled the old grill out, hooked the tabs on the bottom of the replacement into place, positioned the top of the replacement, and replaced the 2 screws. 5 minutes. NOTE: Save the screws, new ones don't come with the replacement grill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lillian from SAN JOSE, CA
- Parts Used:
- W10748097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my pan that browns the meat started to bubble and peal
I really did not have a repair on the microwave just a replacement of the browning pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from CENTENNIAL, CO
- Parts Used:
- W10435116
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drive coupling cracked would no longer rotate turntable plate
used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts
Very Pleased with Parts Select replacement parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zane from ATLANTA, GA
- Parts Used:
- 8205008
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old vent cracked and pulled away from microwave.
The new vent popped right in. Screws easily secured. Same size. Same color. Good as new. Was very simple to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tabitha from STAFFORD, VA
- Parts Used:
- 4393913
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door Latch
Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.
I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock
I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUIS from MIAMI, FL
- Parts Used:
- 8169738
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
DOOR HANDLE BROKE OFF
Disconnected the power. took off top lid. removed door side screws. used two flat screwdrivers to removed door. used the plyers to removed screws that remained so I can reused them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from ELIZABETH, CO
- Parts Used:
- 8169738
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Door handle discintegrated
Had left the small break in the handle go too long, There fore the screw holes in the door had wallowed out. Had to put some small washers in to bridge the wallowed out screw hole. The ends of the handle had broken off on the end of the mounting screws, had to use pliers and the screwdriver to get the plastic mounts off. There was enough room for the washers so no additional adaptation was needed. It all went back together very easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from SAN JOSE, CA
- Parts Used:
- 8184264
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Broken handle
After looking at several UTube videos it was straightforward. The door had to be taken apart which wasn’t easy. The front door had to be taken apart. Then it was easy…:-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from ORANGE, CA
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from Charleston, SC
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
"Lost" microwave tray
Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Naples, FL
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original vent cracked and plastic connections broken
removed old vent and replaced by snapping in and two screws inserted into right and left top connections.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Chapel Hill, NC
- Parts Used:
- 8184592
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door was cracked, running through handle area
Having read a couple of other repair stories, I took out the screws (3 ea) on the end of the door and pried off the front door panel. There was a piece of glass sandwiched in between, and luckily it did not fall and break. Then I removed the handle, which was in good shape and installed it on the new door. The new panel snapped into place and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Orlando, FL
- Parts Used:
- 8184608
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Vent Install
Easy to do. Remove the old screws where the tabs had been broken off. Install new vent and replace screws. MAKE SURE THE TABS ON THE BOTTOM ARE IN THE SLOTS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Mequon, WI
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Had broken previous grille
The most difficult part was getting the old screw out of the top of the grille. Once that was accomplished, the rest was easy as can be. I would highly recommend your service - very good! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mouang from Sacramento, CA
- Parts Used:
- 4393799
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Glass tray shattered
Ordered the glass tray and installed it. Received the orderin about two days.
Was this instruction helpful to you?
Thank you for voting!