KHHS179LBL4 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Foreclosed home: parts were missing
Having the correct model number helps:
Just place the parts in the microwave and it worked.
Just place the parts in the microwave and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HARKER HTS, TX
- Parts Used:
- W11707984
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Microwave had no electrical
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from Dade City, FL
- Parts Used:
- 8185156
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
coupling on top of blender stripped and broken and shaft needed rethreaded
order new coupling and bought die, 10 X 28NF, rethreaded shaft and put cover and new coupling back on. Works fine. Thanks to Parts Select, I was able to rescue a $200.00 commercial blender for about $16.00, parts, and shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herb from Auburn, IN
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
it was working fine and it stopped order a fuse and it wasn't the problem
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Winona Lake, IN
- Parts Used:
- 8206317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Low power - Slow to heat
Replace Magnetron and then I the inverter unit after I discovered the unit still did not heat properly. Inverter had capacitor that was cracked and I found a diode that was flashing over the printed circuit board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from SPRINGFIELD, WV
- Parts Used:
- W11707984
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Maceo, KY
- Parts Used:
- 8169438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The microwave door would not stay latched, so it wouldn't come on.
The repair was easy, I just took off a few screws and found the broken latch spring. The real story is how easy it was to find the replacement spring from Partselect! I couldn't believe they had it, and even better yet, I ordered it one afternoon, and it came the next day with normal shipping! Unbelievable! Then I just popped it in and replaced the covers I had removed and it was working again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Bay Point, CA
- Parts Used:
- 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulbs nedd to repace it.
Took the the want burned out , and put the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JASON from ABSECON, NJ
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plate
Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patti from Coarsegold, CA
- Parts Used:
- 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Burned Out
Followed the instruction booklet that came with the microwave. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kymberly from Beaumont, CA
- Parts Used:
- W10113040A, W10112514A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Grease & Fiter vents
I want to thank PartSelect for thier assistance with my grease and filters that were needed for our microwave. We just bought a home and although the appiances are still in good working condition and only 6 years old they have not been maintaned well at all. The filers needed replacing and our local chain of hardware stores do not carry any of the sizes we needed. I went on line and found PartSelect.com and reviewed what they offered. I really could not find what I needed so I called customer service and the women on the other end of the phone went through in great detail as to the sizes and quantities I would need. I have since then received the filters and they were extremely easy to install and fit perfectly. Very helpful site. KDS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larrt from Minooka, IL
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave turntable stopped rotating.
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dotty from Hillsboro, WI
- Parts Used:
- 8204670
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
surface light on microwave wasnt' working
took the light assembly off and replaced the bulb and put the assembly together and fitted back in the space and finished the assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from tucson, AZ
- Parts Used:
- 8185156
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door handle broken
The screws broke out of the handle. After replacing it with a new one I realized a cheep fix would have been to get longer screws because in the broken handle there was still plenty of thread left. I ordered a new one from Part Select and received it in four days. You first need to remove the black plastic choke around the inside of the door, I used a small flathead screwdriver then remove the two screws on the side of the door. Then with a flathead screwdriver unclip the metal frame from the door skin. Be careful though because at this point the panel can fall out the back. Then move the foam insulation and loosen the screws. Screw in the new handle and the rest snaps right back into place. I would not recomend hiring someone to do this. Its a 15 minute doit yourself project.
Was this instruction helpful to you?
Thank you for voting!