KHMS155LBT2 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Handle and grille we’re cracked
Door handle: open door, remove screws holding door insert and insert putty into door insert to access door handle screws. Screw in new handle and snap door insert back with screws.
Vent grill: remove old grill and replace.
Vent grill: remove old grill and replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from ARVADA, CO
- Parts Used:
- 4393799
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I had broken the glass turn table.
I ordered another one and placed it inside the microwave. It works and fits perfectly. I received the order exactly as scheduled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon C from MEDFORD, OR
- Parts Used:
- W11252182
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Microwave didn't have support ring when house was purchased.
Removed turntable
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Place support ring in track
Place turntable on support ring.
Easy, peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sharon from LAS VEGAS, NV
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turn table cracked needed a new one
easy to replace, just the same as cleaning the turntable and placing back in the micorwave;
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Highlands, NC
- Parts Used:
- 8184146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The grill vent kept falling off.
I loosened the 2 screws at the top, removed the broken-off pieces of the old part, then easily placed the new part and tightened the screws.
The whole process was so easy! It was easy to order the part. It came directly to the house in just a few days.
Thanks.
The whole process was so easy! It was easy to order the part. It came directly to the house in just a few days.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alma from Florence, SC
- Parts Used:
- 8184149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
door got cracked when we remodeled our kitchen
I removed the two screws on the side. Took a putty knife and gently pryed it away from the rest of the door. I took the handle off the old door and put it on the new door. I took the glass and the plastic frame that holds it on off the old door and put it in the new door, I snapped the new door back on and relaced the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from venice, FL
- Parts Used:
- 8184148
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The grill vents lock in tabs were broken off and the grill could not be kept in place
Thank you. The part was easy to find on your web site. The order came within 3 working days and the part replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily C from Brandon, MS
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped the glass cooking tray and it broke in half
Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!
E. Robinson
E. Robinson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Port Saint Lucie, FL
- Parts Used:
- W11256462
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Microwave turns on but did not heat
Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Smithtown, NY
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
machine was dead.
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from Yuma, AZ
- Parts Used:
- 8169738
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced the door handle
It's a simple repair but costly. Just open the door remove the three screws on the side of door. Now use a small screw driver or metal putty knife to remove the chooker collar around the door " be careful this can easly be broken". Okay now the metal inner door is easier to remove if you slightly bend the tabs up around the door. Look carefully you should be able to see where they catch. Once you do that carefully seperate the outter door cover. Careful sometimes it will pop right out and fall. Please no more further repairs needed. Just screw in the new handle push tabs back out on the metal inner door then snap everything back together and reinstall the three screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from W. Dover, VT
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Grill
Snapped and screwed new part in minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from DALLAS, TX
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic on original grill clips broke.
Took out 2 phillips screws on top, pulled the old grill out, hooked the tabs on the bottom of the replacement into place, positioned the top of the replacement, and replaced the 2 screws. 5 minutes. NOTE: Save the screws, new ones don't come with the replacement grill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lillian from SAN JOSE, CA
- Parts Used:
- W10748097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my pan that browns the meat started to bubble and peal
I really did not have a repair on the microwave just a replacement of the browning pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Seymour, TN
- Parts Used:
- 8169738
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken handle (top of the handle actually broke off the screw)
After taking the three screws out of the side of the door, I actually had to get help from my Dad who came over and was able to pry the top corner of the door out of the casing. I was afraid I was going to break the door. Once he got the door pried apart, I was able to replace the handle, clean the entire door and quickly snap it back into place and then replaced the screws.
Was this instruction helpful to you?
Thank you for voting!