YKMHP519ES05 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patrick from MAYS LANDING, NJ
- Parts Used:
- W11025649
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
needed microwave mounting bracket
mounted bracket, case closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GLENDALE, CA
- Parts Used:
- W11256462
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heating up
Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Port Saint Lucie, FL
- Parts Used:
- W11256462
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Microwave turns on but did not heat
Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from LAS VEGAS, NV
- Parts Used:
- W10337248
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sparks from drive coupling
remove 6 lower screws, removed lower panel,2 screws holding drive motor,lower motor, remove old coupling from inside microwave and replace with new coupling, re install motor,install lower panel and screws.no more sparks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WEST NYACK, NY
- Parts Used:
- WPW10466420, W10337248
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable Motor burned out
Unplug microwave
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet
r
Remove bottom of Microwave with phillips screwdriver.
Remove connecting wires to Motor
Remove Motor (2 Screws) with Torx Wrench.
Transfer seal from old motor to new moter
Re-install motor
Connect wires
Reinstall Bottom of microwave
Plug back into outlet
r
Was this instruction helpful to you?
Thank you for voting!
Wrong mounting plate
Two Mounting plates # PS12074431 were sent to me and both do not fit.
Model number MMV1175JZ-0
Serial number TRX-17. 24546
Manufactured April 2020
Contacted Maytag and even sent pictures to show the problem with alignment of the mounting plate not fit in the back of the microwave.
Model number MMV1175JZ-0
Serial number TRX-17. 24546
Manufactured April 2020
Contacted Maytag and even sent pictures to show the problem with alignment of the mounting plate not fit in the back of the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from CARBON HILL, AL
- Parts Used:
- W10337248
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic piece that spins turntable failed because of prolonged heat, I suppose.
Just opened the door and dropped in new part and viola!
Was this instruction helpful to you?
Thank you for voting!
I had a cabinet person install new kitchen cabinets and counter top. After the demolition of the the old cabinets, I had to buy new parts for the new instal
I had the help of a handyman, I'm 75 years young but not handy with tools
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alida from TUCSON, AZ
- Parts Used:
- W10240330
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The glass broke in the light housing
Repair unsuccessful because they sent the wrong part, even after I questioned their selection. It is amazing how a company as large as Whirlpool cannot clearly indicate to the people who work for them how to order the correct part. The fault lies not in the individual who is putting the order in but with the company who cannot take the time to make sure that person is successful in completing their job. Will never buy a product from this company again.
As far as the shipping is concerned. It took forever, just to find out that the part was incorrect.
Better luck next time. right?
As far as the shipping is concerned. It took forever, just to find out that the part was incorrect.
Better luck next time. right?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabra from PEACHTREE CTY, GA
- Parts Used:
- W10337248
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Brand new (open box) purchase from a local appliance liquidator had missing drive coupling. This part holds the glass plate in place and allows it to turn.
It was a very simple and easy fix, no tools needed. First, open the door to the microwave/oven and remove the glass plate and the plastic plate guide. Next, locate the whole in the center. Using your finger, find the drive coupling pin that sits just below the opening (half circle shape). Align the bottom of the drive coupling with the metal pin and press down. Replace the plate guide and plate. The grooves in the bottom of the glass plate should be aligned with the shape of the drive coupling. Test by setting microwave/oven to 30 seconds and watch for proper turning and alignment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BURNSVILLE, NC
- Parts Used:
- W11402532
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broke thw carosel plate
took it out of box wooolaaa fixed thanks fast shipping too...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MIAMI, FL
- Parts Used:
- W10660052
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Micro Wave Steamer
I spoke to Daily via the phone and I ordered a new steamer since my original steamer cracked over a period of time. No installation, no problems I just recently used it and works perfectly! Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from TAMPA, FL
- Parts Used:
- W11402532
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass turntable tray was chipped
Removed the old turntable tray, replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from GLIDDEN, WI
- Parts Used:
- W11025649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mounting plate support edge broken
I removed the microwave to install a back splash and found the support edge on the backplate had broken off and was missing. I searched for parts for the microwave and found them on PartsSelect.com. Easy to order, and was shipped promptly.
Once the part arrived, install was simple, lining up the existing holes. The only hard part was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.
Overall a very simple repair.
Once the part arrived, install was simple, lining up the existing holes. The only hard part was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.
Overall a very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Smithtown, NY
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
machine was dead.
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
Was this instruction helpful to you?
Thank you for voting!