KMHP519ESS1 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard L from PRESCOTT VLY, AZ
- Parts Used:
- 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Charcoal Filter getting old, needed replaced
Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HARKER HTS, TX
- Parts Used:
- W11707984
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Microwave had no electrical
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Was this instruction helpful to you?
Thank you for voting!
Wrong mounting plate
Two Mounting plates # PS12074431 were sent to me and both do not fit.
Model number MMV1175JZ-0
Serial number TRX-17. 24546
Manufactured April 2020
Contacted Maytag and even sent pictures to show the problem with alignment of the mounting plate not fit in the back of the microwave.
Model number MMV1175JZ-0
Serial number TRX-17. 24546
Manufactured April 2020
Contacted Maytag and even sent pictures to show the problem with alignment of the mounting plate not fit in the back of the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Meridian, MS
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Charcoal Filter Replacement
This is an under the counter microwave. Simply removed the two screws holidng the vent grille on top of the unit, lift out the old charcoal filter, clean the vent fan exit surfaces then replace the filter and put the vent grille back. Be careful to not drop either of the two screws after one is installed as you will have to take the grill off and start the screw installation again unless you have a magnetic to retrieve the dropped screw. An easy five minutes at most to change.
Was this instruction helpful to you?
Thank you for voting!
On Turning on the Microwave, it was sparking, was not sure where the sparks are coming from, initially I thought mica at the end of megnatron duct could be the issue
when I opened the back cover of microwave, the diode was kind of blackish blown, since there was light bulb and fan were still working, i thought it could be problem with any one of the components like; magnatron or capacitor or diode, so first replaced the diode and mica at the end of the magnatron duct, there was problem with door switch as well. i fixed that too. Now it is working. It cooks bit faster, Wondering why?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Wilmington, OH
- Parts Used:
- W10337248
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The support became distorted and needed to be replaced.
I simply lifted out the glass rotating plate and inserted the new support. How complicated can that be?!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herb from Auburn, IN
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
it was working fine and it stopped order a fuse and it wasn't the problem
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from SPRINGFIELD, WV
- Parts Used:
- W11707984
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Oakland, NJ
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
changed filters
Replaced filter which came inrecord time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from New Berlin, WI
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Clearing the clean code was the hardest part.
I had no problem installing the new filter. Just used a phillips screw driver to remove the two screws holding the vent cover in place. Cleaned the dust out of the ducts and reinstalled the new filter. The screws must be held to the screw driver with your finger tips so you don't drop them in the vent cover. The most difficulty I had was in clearing the clean code from the screen. There are no instructions in the owners manual for doing this. But after several tries I got it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from brockton, MA
- Parts Used:
- W10709921
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I noticed that the hood lights were out.
I took off the glass panel underneath the microwave and replaced the 2 bulbs in less than 3 minutes by myself with only a phillips head screwdriver. I was very pleased with the service I received and more pleased with myself that I did not have to call in a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carole from North Canton, OH
- Parts Used:
- 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
in 2 yrs the charcoal filter had NEVER been changed and it was smelling horrible--so had to be done !
--simpley removed 2 screws, removed old filter--but had PLENTY of cleaning to do before putting in the new filter !My husband LOVES to cook and pan fry foods--it won't go that long before being replaced in the future!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Southfield, MI
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace filter
Time to replace the charcoal filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethel from New Berlin, WI
- Parts Used:
- 8206230A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed a clean filter
Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from North Olmsted, OH
- Parts Used:
- 8206230A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Reminder signal and message to change filter on microwave digital display.
Removed 2 screws on the top of the microwave and removed top/front piece of microwave. Slid out old filter (which didn't look dirty at all) and replaced it with the new one. Replaced top/front piece and 2 screws. It took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!