79048859900 Kenmore Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glyndon from BOWLING GREEN, KY
- Parts Used:
- 318254906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Bake element burnt out
Tool old elentment out, put new element in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from REYNOLDSBURG, OH
- Parts Used:
- 318261230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
door latch motor not working
remove oven door, disassemble front of glass top range then basically
it was just plug and play then reassemble be careful oven door is heavy
it was just plug and play then reassemble be careful oven door is heavy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan M. from Sierra Madre, CA
- Parts Used:
- 318212210
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Inner window on my Frigidaire electric stove oven cracked
On this website, I found an instruction manual for this stove. There were 2 pages about how to change the glass on the oven door, including diagrams. I'd also checked a generic youtube video on changing inner glass on oven doors too, although the hinges in the youtube demo weren't exactly like those in mine. I printed out the instructions, checked the oven door to make sure the hinges looked like those in the diagrams, set aside a couple of hours on a free day with no other distractions, and did the job. I just kept removing screws from the inside oven door, peeling back the layers of the onion, until I got to the innermost glass, which was cracked. Put the new glass in, put it back together. On youtube the guy said it would take 20 minutes. It took me about an hour. Saved a ton of money by doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from Depoe Bay, OR
- Parts Used:
- 5304493153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Timer runs, but no heat.
I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Selma, CA
- Parts Used:
- 5304493153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Microwave Would Run And Count Down But Not Heat
Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adam from new orleans, LA
- Parts Used:
- 5304493153
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Power, light, and clock work, micro/turntable not working
Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Cypress, TX
- Parts Used:
- 5304493153
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Instructions did not match the assembly of the ice maker.
I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply on my ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Glasgow, MT
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorenza from Rowlesburg, WV
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Improper temperature when baking.
Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!
Was this instruction helpful to you?
Thank you for voting!