Models > 79047859404 > Instructions

79047859404 Kenmore Microwave - Instructions

Jump to:

All Instructions for the 79047859404
46 - 60 of 72
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Oscar from Scranton, KS
Parts Used:
316217002
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
F10 Error. Temp sensor at 1189 room temp ohms
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Denise from Landover, MD
Parts Used:
316538904
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light bilb went out
replaced it
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joshua from Depoe Bay, OR
Parts Used:
5304493153
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Timer runs, but no heat.
I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Selma, CA
Parts Used:
5304493153
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
Microwave Would Run And Count Down But Not Heat
Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tony from Hartford, CT
Parts Used:
5304409888
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sue from Lampasas, TX
Parts Used:
5304409888
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
adam from new orleans, LA
Parts Used:
5304493153
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Power, light, and clock work, micro/turntable not working
Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harry from Cypress, TX
Parts Used:
5304493153
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Instructions did not match the assembly of the ice maker.
I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply on my ice maker.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharon from Foley, AL
Parts Used:
5304524341, 316538904
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
0 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Amy from Corona, CA
Parts Used:
5304524341
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Glasgow, MT
Parts Used:
316217002
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Oro Valley, AZ
Parts Used:
318255605
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
broiler element burned out
watched a U-Tube video on this subject.....worked like aa charm!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
CARL from MARSHALL, WI
Parts Used:
318053120
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
burnt door seal
with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Portland, OR
Parts Used:
5304440845
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My wife reported that she saw flames coming up the inner wall of the microwave oven.
I noticed that the scorched and slightly melted plastic was above a little piece of what looked like cardboard, so I did a Google search for "flames in microwave" or something similar and found a link to a DIY repair site that mentioned a tear in the waveguide cover causing that problem. I ordered a replacement from PartSelect, received it in near-new condition, and replaced the old one with the new one in 5 seconds. I then called PartSelect to let them know that the new part had a couple of "wrinkles" in it that I was concerned might cause a problem down the line but that it seemed to be working OK for now. The nice person in customer service told me that I could use the part for the full year of the warranty and return it if a problem arose. I'm very satisfied with the experience!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lorenza from Rowlesburg, WV
Parts Used:
316217002
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Improper temperature when baking.
Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 79047859404
46 - 60 of 72