66568681891 Kenmore Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- sharon from LAS VEGAS, NV
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turn table cracked needed a new one
easy to replace, just the same as cleaning the turntable and placing back in the micorwave;
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Smithtown, NY
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
machine was dead.
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Port Saint Lucie, FL
- Parts Used:
- W11256462
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Microwave turns on but did not heat
Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily C from Brandon, MS
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped the glass cooking tray and it broke in half
Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!
E. Robinson
E. Robinson
Was this instruction helpful to you?
Thank you for voting!
The old coupling melted and the tray cracked in half.
It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois P from Morris, IL
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke rotating plate, it fell off counter after being washed
Opened door and put new plate in.
Placed order on Thursday evening and received Sat Am
Placed order on Thursday evening and received Sat Am
Was this instruction helpful to you?
Thank you for voting!
smoke alarm went off while frying
both of the pieces have a tab that help remove the pieces. They slip right out and new ones are putin place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Pine, CO
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replacement of hood light bulbs
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SM from JAMESTOWN, RI
- Parts Used:
- 6800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
On-door water/ice dispenser lights failed, paddles did not work to dispense
It took me time to remove the parts and suss out the issue, but the repair itself was EASY. A wire ribbon connected to the circuit board had gone bad. One Phillips head screwdriver, 7 screws, to get at the old one, pull it out, replace it with the newly ordered part. NO PROBLEM. Ladies, you can do IT!! You have the power!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tabitha from STAFFORD, VA
- Parts Used:
- 4393913
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door Latch
Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.
I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock
I replaced the latch on the microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from EL DORADO HLS, CA
- Parts Used:
- 8184599
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Missing microwave vent grille
2 screws only. Less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from HILTON HEAD, SC
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Exterior light bulb (PS2376034) broken off in socket. No access for pliers after glass cover removed.
Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from MARSHALL, MN
- Parts Used:
- 8184599
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cracked ( broken ) vent grille.
It was real easy. Took out four screws and put new unit on with the four original screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from ORANGE, CA
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from STANWOOD, MI
- Parts Used:
- 8169573
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Door frame
I followed the excellent instructions on the Partselect website.
I removed 4 screws and the frame popped out, I cleaned the glass and reassembled. I was surprised how easy.
Thanks for your help.
Michigan Customer
I removed 4 screws and the frame popped out, I cleaned the glass and reassembled. I was surprised how easy.
Thanks for your help.
Michigan Customer
Was this instruction helpful to you?
Thank you for voting!