66588539900 Kenmore Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cynthia from DRIPPING SPGS, TX
- Parts Used:
- W11661547
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
Changed out turntable motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HARKER HTS, TX
- Parts Used:
- W11707984
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Microwave had no electrical
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luiz from Washington, DC
- Parts Used:
- 8205994
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lost the driver
just insert it in the right side
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Mechanicsville, VA
- Parts Used:
- 8206499
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost spring that holds filter in hood that was lost when cleaning it.
simply removed the filter casing from the microwave, then removed both filters and inserted the spring after bending it slightly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herb from Auburn, IN
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
it was working fine and it stopped order a fuse and it wasn't the problem
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from SPRINGFIELD, WV
- Parts Used:
- W11707984
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Bay Point, CA
- Parts Used:
- 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulbs nedd to repace it.
Took the the want burned out , and put the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patti from Coarsegold, CA
- Parts Used:
- 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Burned Out
Followed the instruction booklet that came with the microwave. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from Antioch, CA
- Parts Used:
- W10120840A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty filters
Removed the dirty ones and put in the new ones. This was really not a repair. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from payson, AZ
- Parts Used:
- W10120840A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
need new filter
replaced old filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Hanahan, SC
- Parts Used:
- W10120840A, W10120839A, 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bulb Finally went out
Used an apex bit unscrewed the fittingand down came the light cover. Pulled the old bulb out and had to use a flashlight to line the prongs up to install the new one. Whileeverything was down used an oven cleaner to degrease and clean EVERYTHING. You wouldn't beleive how much grease and debris will accumulate in 5 years. And I only fry bacon once in a blue moon. All in all it was simple to order, clean, and repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Red Oak, IA
- Parts Used:
- 8204670
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light burned
Unscrewed the lens cover anbd inserted the new bulb. Put the cover back on and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Anoka, MN
- Parts Used:
- 8204670
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out overhead light
Some difficulty getting screw loosened, once that was done replaced burned out bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Mason, OH
- Parts Used:
- W10120840A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace charcoal filter
Took old one out,and clipped new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dotty from Hillsboro, WI
- Parts Used:
- 8204670
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
surface light on microwave wasnt' working
took the light assembly off and replaced the bulb and put the assembly together and fitted back in the space and finished the assembly.
Was this instruction helpful to you?
Thank you for voting!