36362709200 Kenmore Microwave - Instructions

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

1. Turned off circuit breaker for microwave.
2. Removed screws holding the bottom cover of the microwave; cover is hinged at the back, so it dropped open and stayed out of the way.
3. Unplugged turntable motor and removed screws that hold turntable motor in place.
4. Pushed broken pieces of the plastic turntable coupler out of the way (hole for motor's axle not big enough to remove them).
5. Put turntable coupler into hole in bottom of microwave interior, held it in place while putting the motor axle into it from below.
6. Replaced screws holding turntable motor in place, plugged in motor's electrical connector.
7. Closed bottom cover and replaced screws that hold it in place.
8. Switched on microwave circuit breaker.

After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.

Unplugged the stirrer motor and the noise stopped. Therefore, replaced the stirrer motor.

unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

Fortunately I had my handyman here to repair a leak under my kitchen sink and asked him to replace the handle on my microwave. There were no instructions included with the handle but I had printed out descriptions from the web site of what others had done. He pried off the inside of the door which revealed two screws, which he removed. He then had to pry off another covering which revealed the other two screws that removed the handle. He attached the new handle and put the two parts that were pried off back on. It would not be an easy process for the ordinary householder and it would have been nice if detailed instructions had come with the handle (with pictures showing exactly which areas of the door needed to be removed). I was going to try the repair myself but am extremely glad my handyman was there as I probably would have ruined the microwave and would have had to purchase a new one. Kudos to my handyman.

Ordered and replaced turntable coupler. Still didn't work.
Ordered turntable motor. Left bottom of microwave open for motor to arrive since the parts are shipped so quickly. Sure nuff parts arrived 3 days later, replaced and walla walla fixed in 10 minutes. Simple, simple.

I removed the broken turntable coupling and popped on the new one. Simple as that. It was a 2-minute job.

I followed the instructions provided by others on-line who had done a similar repair. I removed a handful of screws, disconnected the wires from the old drive motor and connected them to the new drive, replaced the screws that held the drive motor in place, and those that held the bottom housing in place, and I was done. Literally took less than 10 minutes. If I had known earlier how easy it was, the microwave would have been fixed much earlier.

First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.