72180404402 Kenmore Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Susan from HENDERSON, NV
- Parts Used:
- 6549W1S013H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave dish would not move back and forth
unscrewed the bottom of the microwave and unplugged old part then took the screw out and put new one in. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from MORENO VALLEY, CA
- Parts Used:
- 4900W1A001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wanted to see the instructions before I install it.
Wanted to see the instructions before I install it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dick from SANDY, UT
- Parts Used:
- 6600W1K001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave fan would come on when door open. Timer and unit would not switch on.
I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.
https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni bc from PORT ORANGE, FL
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch broken... Spring off
You Tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from CARY, NC
- Parts Used:
- 6549W1S013H
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave turn table not working
Removed the phillips screws from the base.
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg J. from WEST CHESTER, PA
- Parts Used:
- 4026W2A019A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Latch spring keeper broke
Removed door from microwave and then popped the inside widow trim ring off. Removed 4 screws from the window bracket, replaced the latch with a new part and then assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from CHURCH HILL, MD
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light bulb replacement
very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Oak Ridge, TN
- Parts Used:
- 3B74133Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave operated but did not heat
Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Burke, VA
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out
I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from Daleville, VA
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would not heat food, but everything else worked.
Problem was a faulty door latch switch. I easily accessed the switch by removing the control panel, total of 4 screws. After that, just disconnected the three switch door latch assembly and connected the new one. Took about half an hour and was very easy. Unit works perfectly now.
Was this instruction helpful to you?
Thank you for voting!